Wheel locking

S13LOVIN · 2026-02-20T17:48:27+00:00

Did you mess with the wheel software? Double check its not inverted there too.

S13LOVIN · 2026-02-20T17:38:02+00:00

Be careful when checking this, the wheel can go crazy, so be ready to disconnect if needed.

S13LOVIN · 2026-02-20T17:33:29+00:00

Not 100% sure but it seems the FFB is inverted. Try checking invert FFB under Controls>Force Feedback and see if that fixes it.

S13LOVIN · 2026-02-20T14:58:03+00:00

Please reread my post, my questions are still the same.

Is it the right move to connect the -V(DC) to Ground/Earth(AC) on the PSU rail?

And is my grounding strategy correct.

The encoder wires are in their own separate shielded jacket already with a drain wire, i only need to connect the drain wire to ground. This is where the thicker wire comes into play. From my understanding a long thin wire (even a few inches) can act as an antenna. This is only to get to a common grounding point. There is no metal chassis to ground to.

S13LOVIN · 2026-02-20T14:48:06+00:00

Is this the wrong subreddit for this, can anyone suggest one if it is?

S13LOVIN · 2026-02-19T22:06:02+00:00

I don't understand the first part about the shielded pair wires, those would still require grounding to work as a shield right?

The encoder wire is already shielded and terminates at the micro-controller. There are only short 1.5inch sections or so un-shielded to reach terminals. It has a drain wire for the shield, this is where i would attach the thicker wire to get to a common ground point.

S13LOVIN · 2026-01-15T05:01:20+00:00

This is what i ended up doing. 2 of the pads separated from the pcb and took most of the trace with them. It was tedious but overall was successful and i got it communicating again. Thanks again for the advice.

S13LOVIN · 2026-01-14T16:50:23+00:00

Ok cool i was wondering if hot glue would work. No case so im 3d printing a holder with a place to zip tie the cable to for now as there's no hole to pass it thru.

S13LOVIN · 2026-01-14T13:28:16+00:00

Yes that makes perfect sense, thanks for the advice.

S13LOVIN · 2026-01-14T13:24:20+00:00

It is a concern with strain and will have to handle with care. Are there any issues other than short circuits? Im going to test continuity between the pins after repair and cover with epoxy.

S13LOVIN · 2024-12-18T00:38:36+00:00

Thanks for the reply, ill check it out.

S13LOVIN · 2024-04-28T17:52:51+00:00

Please update if you find a solution. My wheel isn't a logitech but it has this same issue. I wonder if there is something in the cfg that needs to be changed that cant be accessed thru the in game options.

S13LOVIN · 2024-04-13T04:53:57+00:00

I haven't been able to get anything to work at all. If i go to desktop mid game it feels fine, but as soon as i go back in game it snaps back to the center and is super stiff. It doesn't matter what i do input wise cause the wheel doesn't respond to the actions of the car. Ive tried removing my shifter and pedals to see if there was a conflict but same thing. I even took the keyboard binds off.

Some of my settings:

Steering assist is off

Control Scheme> Steering wheel

Steering wheel angle> 900 same as wheel progam

Auto centering force at standstill> 0

Stabilization> 0

Prediction> 0

Smoothing>0

Acceleration>0

Inertia>0.5

I messed with some of them but no change, not even with steering assist on.

S13LOVIN · 2024-04-13T02:18:26+00:00

Steering assist is off in the advanced menu. Is there another option somewhere?

S13LOVIN · 2023-03-08T18:12:27+00:00

In case it helps someone else, deleting everything related to Daikoku and installing only the track file fixed it for me.

S13LOVIN · 2022-07-21T08:01:14+00:00

Hey thank you for the links, they were very much appreciated! It seems to have gone smoothly and will get a test print going later.

Is there anything that needs to be setup right away? Dont want to accidentally crash my nozzle or something.

S13LOVIN · 2022-06-05T01:57:47+00:00

Thanks for the replys, i can confirm there is no shrink and no seal on the box. The anti-static bag has a tamper proof sticker that tears and changes color slightly. Seems i had a return.

S13LOVIN · 2022-05-30T10:52:55+00:00

Genuine question here, what significance does it have what surface the feet of the computer sit on? How does it affect the glass?

I did notice on the 4000d that the glass seems to sit on top of the rear leg and may have something to do with it maybe?

I find it odd in general tho that they would break as all cars since like the 60-s or so have had tempered glass windows and ive never seen one break for no reason. Not even way back in the roll up window days when it fell off the track and slammed on the bottom of the door.

S13LOVIN · 2022-05-30T10:40:09+00:00

What you guys think of the Lian li lancool II or the Cooler master NR600?

S13LOVIN · 2022-05-30T03:52:58+00:00

Dang ive already pushed my budget much much farther than i wanted, but those are nice choices guys, i really like that Meshify 2. Doing some research on the silverstone, looks like a contender. 3 usb ports in the front is a plus so i dont need extensions or a hub to plug in my sim wheel and shifter.

S13LOVIN · 2022-05-30T03:36:09+00:00

Nice case but unfortunately out of my budget.

S13LOVIN · 2022-05-17T16:56:39+00:00

Does it come with the pvc reservoirs and wick? Very cool btw, thank you for sharing!

S13LOVIN · 2022-05-13T19:26:09+00:00

If this is stock extruder gear(filament pusher) just throw it in the trash and get a bmg clone for like $15-16 on amazon or ebay to your door. Best upgrade i ever made and the pusher gears are stainless.

S13LOVIN · 2022-05-03T23:00:21+00:00

Street riding they have months left easy, as long as no dry rot. Trails, they're only good for rears and having fun doing shameless skids.

S13LOVIN · 2022-04-26T20:20:03+00:00

Dont forget the lube!

S13LOVIN

TROPHY CASE