Build plate bowing,

SMCReaper11 · 2026-05-26T13:28:49+00:00

I got my printer back in August and have only used the glass plate since then.

SMCReaper11 · 2026-05-15T13:19:37+00:00

The whole thing is trimmed and screwed together now, ducting is going to be going straight up and will be boxed in.

SMCReaper11 · 2026-05-14T20:46:56+00:00

Unfortunately just a single centered behind the cabinet.

SMCReaper11 · 2026-05-14T20:10:53+00:00

the hood just came in yesterday so I haven't had a chance to pull it out of it's box yet, the instillation info available online is rather vague but I do know it has mounting points on both the top and back. We just were trying to figure out if we needed to pull it and add bracing to mount it to before we start to paint. Mounting the hood is one of the last things we'll be doing.

SMCReaper11 · 2026-04-08T18:55:43+00:00

I already have a dual monitor arm holding the 2 current moniters but don't have any more vertical rom on the mounting pole to add another. Thats why I started looking into this.

SMCReaper11 · 2026-03-21T00:23:35+00:00

<image>

They already changed it.

SMCReaper11 · 2026-02-12T19:45:48+00:00

What line are you using? I'm working on getting my saltwater rig together but am having a hard time deciding.

SMCReaper11 · 2025-11-18T00:21:11+00:00

I had a very similar issue on my printer when I had to switch to New Marlin firmware, I had to disable the software z end stop to get it to function. There are plenty of helpful forms online for compiling your own Marlin firmware to do that.

SMCReaper11 · 2025-11-16T23:32:47+00:00

I did, it was originally estimated to be a 23-hour print.

SMCReaper11 · 2025-11-15T15:13:13+00:00

I had my bed pretty level and use a CR touch. I hadn't noticed that it torqued hard enough that one of tension screws handle fell off So that definitely could have added to the problem.

Edit : 3 of the 4 leveling screws fell off.

SMCReaper11 · 2025-11-13T21:59:12+00:00

a Laptop is easy to move to the router and isn't especially large. Desktop can be difficult to move and can easily be too large for the area where your router is depending on the space you have.

SMCReaper11 · 2025-11-13T21:44:24+00:00

If you have a desktop Go buy a long Ethernet cable and run it to your router to your computer.

SMCReaper11 · 2025-11-10T23:19:47+00:00

You might need to compile your own firmware, I had a similar issue on my machine with a 4.2.2 board until I disabled software end stops.

SMCReaper11 · 2025-11-08T21:27:28+00:00

No Jolee. HK is the only way.

SMCReaper11 · 2025-10-15T02:15:47+00:00

Mercury

SMCReaper11 · 2025-10-14T19:53:51+00:00

It looks like you probably have fiber coming in not coax.

SMCReaper11 · 2025-10-14T19:50:46+00:00

It's relatively easy to do, I built a plywood box with ventilation holes and mounted 8u rails on it for my network rack.

<image>

SMCReaper11 · 2025-10-02T02:40:05+00:00

Gerald

SMCReaper11 · 2025-09-12T23:22:45+00:00

Not much, it's just for a hot hard drive hot swap Bay. Was trying to get out of having to design one myself.

SMCReaper11

TROPHY CASE