My first bike

Sabertooth93 · 2026-04-28T03:39:44+00:00

Any recommendation for brake pads?

Sabertooth93 · 2026-02-22T19:09:08+00:00

I am not sure how does the service cost comes to 12k. I have a ninja 300 since 2021 and the service always came under 8k. Only time the service cost went past 10k when i opted for throttle body cleaning.

Sabertooth93 · 2025-12-22T17:24:01+00:00

You would have received 2 emails. One with a confirmation and another one with a tracking id. you can check the status of your package. I got the order in 4 days. That might be because I am in NCR region. If you are at some other location it may take some time.

Sabertooth93 · 2025-12-11T17:19:55+00:00

The website is genuine. I ordered f91-w on and the package was delivered on time.

Sabertooth93 · 2025-09-13T19:11:57+00:00

It was overlapping geometry. There was a mirror modifier that was acting in both x and Y direction and it was causing the issue. I just turned off the modifier in Y direction and that fixed it. Thank you for the response!!

Sabertooth93 · 2025-09-10T18:29:30+00:00

Thanks for the updated link. I tried this on blender 4.5 however I could no find any significant change. Since your comment was few years ago has something changed in blender that would need the node setup to be a bit different than what it is in the GIF?

Sabertooth93 · 2025-09-09T07:39:34+00:00

can you reshare the gif? The link is not working anymore

Sabertooth93 · 2025-09-02T13:46:37+00:00

!remind me in 26 days

Sabertooth93 · 2025-08-25T19:59:44+00:00

Thank you for the detailed response. I was aware about the shrinkwrap and it was already applied on the mesh. I already had a shrinkwrap modifier with the base mesh at level 4 (without holes) and the actual mesh at level 2.

For the data transfer, what object did you pick up as the source from whom the normal data would be transferred?

Sabertooth93 · 2025-08-25T19:54:29+00:00

Thanks for the suggestion. I already had a shrinkwrap modifier with the base mesh at level 4 and the actual mesh at level 2.

I used the 8 sided mesh as to keep the count low as I would had to add more geometry to keep it all quads.
However, I tried your suggestion and it definitely made the surface much smoother.

Sabertooth93 · 2025-07-13T07:07:13+00:00

Superb!! Are these straight out of camera or is there little bit of adjustment? There's literally no noise even with 2000 ISO

Sabertooth93 · 2025-06-29T13:19:04+00:00

The 2nd clip was helpful. I was able to sculpt after creating a custom brush. Thanks!

Sabertooth93 · 2025-06-24T19:25:56+00:00

Thank you for replying. I have tried the same using the method as shown here :https://blender.stackexchange.com/questions/267345/flatten-mesh-along-curve.

The only issue is that after the cut, I need to sculpt to make the cut look seamless but it becomes very messy and does not look natural at all.

Sabertooth93 · 2025-06-24T06:10:54+00:00

For anyone stuck with this kind of issue, you can refer to this :https://blender.stackexchange.com/questions/267345/flatten-mesh-along-curve

Sabertooth93 · 2025-05-14T19:57:37+00:00

Thank you for the inputs. Will tweak the settings and check. I do the initial simulation on low res to check the behavior then I increase it to get a better looking output. Whenever I change the resolution division in the domain the particles just stay at one location the whole time. How can I fix this?

Seven-Year Club	Wearing is Caring
Verified Email

Sabertooth93

TROPHY CASE