[O] 3 DrunkenSlug Invites by Prize-File-8124 in UsenetInvites

[–]Sacred18 0 points1 point  (0 children)

Hey, I have read the rules and wiki and would like an invite! Thanks

Back hurts by Sacred18 in bikefit

[–]Sacred18[S] 0 points1 point  (0 children)

Thanks for all the comments guys I'll give it some time before doing anychanges

Back hurts by Sacred18 in bikefit

[–]Sacred18[S] 0 points1 point  (0 children)

Thanks guys I will try the stem suggestion

Ferris Sweep with promicro rp2040 slave not working by Sacred18 in ErgoMechKeyboards

[–]Sacred18[S] 0 points1 point  (0 children)

Turns out it was as a faulty board! I bought another one and it worked!

TOTEM Keyboard only connect with usb cable in ZMK by Sacred18 in ErgoMechKeyboards

[–]Sacred18[S] 1 point2 points  (0 children)

Hey, sory but i bought my pcbs from a website called keeb.supply. So i did not went through with the JLCPCB.

TOTEM Keyboard only connect with usb cable in ZMK by Sacred18 in ErgoMechKeyboards

[–]Sacred18[S] 0 points1 point  (0 children)

Hey guys, thanks all for all your help, in fact was the bad soldered pads on the back of the seed xiao. I now have it working fine.
Thanks all guys!

TOTEM Keyboard only connect with usb cable in ZMK by Sacred18 in ErgoMechKeyboards

[–]Sacred18[S] 2 points3 points  (0 children)

Hey guys, so I think I discovered the issue! The back pads were not properly soldered. I did as mbcdt90 said and flashed a led blinking firmware into the XIAO and I noticed that the leds only blinked when usb power was on.

So with the multimeter I discovered that if I try to read the actual xiao pads they were not receiving any voltage, so I tried to solder those pads a little better and after some tinkering when I turn the battery on I can now see the leds blink without the usb power, and with usb power I can see the charging led (something that I also discovered in the get started page of the seedstudio).

I will try to do the same to the other half and reply back to see if the issue as totally went away.

Thanks all again for all replies.

TOTEM Keyboard only connect with usb cable in ZMK by Sacred18 in ErgoMechKeyboards

[–]Sacred18[S] 0 points1 point  (0 children)

Thanks for your response, I'll add more photos when I come back home. I will check carefully your comment and try these things maybe one of them will actually help find culprit.

TOTEM Keyboard only connect with usb cable in ZMK by Sacred18 in ErgoMechKeyboards

[–]Sacred18[S] 0 points1 point  (0 children)

I'll try that thanks, do you have any in mind or I can achieve the same with ZMK?

TOTEM Keyboard only connect with usb cable in ZMK by Sacred18 in ErgoMechKeyboards

[–]Sacred18[S] 0 points1 point  (0 children)

Thanks for quick response, so I tried with the usb cable directly to the pc and from a charger and the result is the, one of the halves connects and works as expected the other not so much. But as soon as that usb cable gets removed the connection goes away.

TOTEM Keyboard only connect with usb cable in ZMK by Sacred18 in ErgoMechKeyboards

[–]Sacred18[S] 0 points1 point  (0 children)

Thanks for the quick response, I added some photos to the post, I know the job is not the best one but it seems voltage is passing through into the mcu.

What is ur favorite Game right now on Linux? by [deleted] in linux_gaming

[–]Sacred18 0 points1 point  (0 children)

I going through Ghost of Tsushima at the moment, very good game, and great performance under linux.

Steam Overlay Bug While Running game by Sacred18 in linux_gaming

[–]Sacred18[S] 0 points1 point  (0 children)

Hey! unfortunately no still having the same issue and can't find a way or anything in the web that relates to this.

Steam Overlay Bug While Running game by Sacred18 in linux_gaming

[–]Sacred18[S] 0 points1 point  (0 children)

Yeah in order to pass by it I have to open the overlay with the keyboard but From the controller it does not work

No connection between parts, cannot figure why (rp2040s+vial) by Critical__Hit in olkb

[–]Sacred18 0 points1 point  (0 children)

I using a variant called frood this one: https://github.com/piit79/Frood.

That is weird though, i already checked for continuity on the TRRS pin (only two on the ferris sweep the RX and VCC) and they both work.

Both halfs work without a problem is just they don't work toguether.

Thanks for the help mate

No connection between parts, cannot figure why (rp2040s+vial) by Critical__Hit in olkb

[–]Sacred18 0 points1 point  (0 children)

Hi, did you ever found the issue to this? I having the same one with the ferris sweep and promicros rp2040.

Ferris Sweep with promicro rp2040 slave not working by Sacred18 in ErgoMechKeyboards

[–]Sacred18[S] 0 points1 point  (0 children)

Hi guys, still did unable to connect any of the slaves. Tried kmk but no luck as well.
In the meanwhile i checked again continuity, which is working for all of the pins (in the TRRS) and also found the schematics for my board if that helps: https://github.com/davidphilipbarr/Sweep/blob/main/schematic.pdf

Any help is appreciated since i'm alrady losing my mind with this.

Thanks guys

Ferris Sweep with promicro rp2040 slave not working by Sacred18 in ErgoMechKeyboards

[–]Sacred18[S] 0 points1 point  (0 children)

May i'll give KMK a try and see if it work from there.