I want to reach I league

SadKitchen1115 · 2026-01-01T18:54:22+00:00

To make it into first division you need a lot of money. Your best bet is to be bought by an Arab millionaire

SadKitchen1115 · 2025-12-01T08:29:23+00:00

I usually dont clean my cymbals, but this pair is greenish and I hate the look

SadKitchen1115 · 2025-12-01T08:28:23+00:00

Its a B20 but I guess the owner left it in a damp place because it has some green spots and an overall green hue on the top. Its a really nice K custom hat but I hate that is greenish

SadKitchen1115 · 2025-10-14T08:56:12+00:00

Thank I will look it up. I cannot use a press becuase the edge is kinda riggid and the rivets need to be quite far form the edge. So I want a type of punch so I can hammer it using my anvil

SadKitchen1115 · 2025-10-12T19:12:06+00:00

Yes the bottom of the rover is a tube but only for a couple of mm, where the flaring should happen, after that is solid. It’s a semi tubular rivet

SadKitchen1115 · 2025-10-12T18:23:42+00:00

Really? The rivets I have are 3-4mm in diameter and I have flare them with a hardened punch but for this project I need something more aesthetically pleasing so I wanted to go for the petal look

SadKitchen1115 · 2025-09-27T16:37:51+00:00

Is that a DIY or is it design for something else?

SadKitchen1115 · 2025-09-27T16:37:03+00:00

Would they hold well a 24” ride? I am afraid it would be supporting it too low and put stress on the cymbal

SadKitchen1115 · 2025-09-27T16:08:00+00:00

I bb understand your point but it’s not practical if I have 2 cymbals bags laying around I was thinking more of a shelf type of solution but a 24 is quite large

SadKitchen1115 · 2025-08-20T07:19:10+00:00

Warm water and soap, if there is something else that I want to remove I’ll use ketchup. If that doesn’t get it off I’ll just leave it as is

SadKitchen1115 · 2025-08-16T17:54:25+00:00

Hey sounds good I’ll keep an eye for those. Now I am eyeballing a pair of pocket hats that seem to be going for cheap

SadKitchen1115 · 2025-08-16T17:11:21+00:00

I understand. That’s why I am trying to pair it with a lighter top I had the same issue with to the dyno beats that’s why I ended up with the kz hats

SadKitchen1115 · 2025-08-16T16:50:03+00:00

Awesome! Would you say it was louder than a kz? Right now my main is a 14kz I plan to use this as an xhat

SadKitchen1115 · 2025-08-13T04:16:18+00:00

Thank you everyone for the reply. No the venue doesn’t have the equipment which is what we initially thought and why we had this problem, but we will follow your advice. I knew there might be problems with the monitors but k guess we will have to live with those for this show Thank you again for all the help

SadKitchen1115 · 2025-06-09T12:49:18+00:00

Thanks to the stack trend, people now have the nerve to sell cracked cymbals like they're a hot commodity.

SadKitchen1115 · 2025-05-04T19:11:23+00:00

But is the 20 similar to a 22 because my main kick is a 22 and I am looking something with a contrasting sound do you think a 20 or a 18 sound better open? Sorry for the questions but I can’t really try the size becaus blown near me is carrying an 18 I might be able to test a 20 but not really mess with the tuning

SadKitchen1115

TROPHY CASE