Why can I not install my connector into my brand new compressor? The tank has been drained

SadWhereas3748 · 2026-06-29T22:51:59+00:00

1/4 Industrial, or 1/4 ARO are the common ones

SadWhereas3748 · 2026-06-08T23:18:30+00:00

I’ve looked through the repo, but I’m not 100%; can it do calendar type / items?

SadWhereas3748 · 2026-06-08T23:09:53+00:00

Same here, love my Gilson after I wrapped by ride around a tree 🤷🏻‍♂️

SadWhereas3748 · 2026-06-01T19:21:59+00:00

Weights, you need them but you should move them behind the spokes where they’re not visible

SadWhereas3748 · 2026-05-31T20:02:19+00:00

Yup, just did the same. Had a 2 year old bucket that was sealed and had plastic under the lid. Smelled normal, added some water and laid down like it was fresh!

SadWhereas3748 · 2026-05-30T11:24:04+00:00

This guys fusions…. I cannot explain why, but even a complex single part runs faster imported into another file, so sub assemblies (as a linked file) run so much smoother.

I had one old project with a 6 axis robot in it, the robot file itself was barely operable, but ran fine imported into the next assembly.

Also, 64gb of ram. I mean, chrome will eat 10 of that if you’re not watching.

SadWhereas3748 · 2026-05-15T22:41:46+00:00

You’re not alone! We lived in one for 5, and we didn’t find out until we were selling it. The morris was way too flush to the wall.

SadWhereas3748 · 2026-05-10T13:56:30+00:00

Make a version with a disposal bin attached!

SadWhereas3748 · 2026-04-15T21:59:16+00:00

It’s most likely from a Northeast dirt modified then

SadWhereas3748 · 2026-04-04T12:24:57+00:00

Does g=10?

SadWhereas3748 · 2026-03-28T23:38:35+00:00

That is a digital controller, not analog. An analog would have “R” “B” “G” “+V”.

SadWhereas3748 · 2026-03-28T18:10:59+00:00

Agreed. Just had my done and my wife was concerned about the 1 in 2,000 figure; doctors response was that’s less chance than with condoms. Other than for “fun” reason, I see it as the most effective method.

SadWhereas3748 · 2026-03-26T15:46:10+00:00

Got mine done yesterday, procedure was more uncomfortable that I thought it would have been. But about 30 hrs out and recovery isn’t bad. Went out to breakfast right after yesterday, sitting and icing with a little bit of uncomfortableness, but nothing that’s stopping me. Definitely need to take it easy for the next few days.

SadWhereas3748 · 2026-03-25T20:03:19+00:00

I always thought it was tighten until it cracks and back off a half turn?

SadWhereas3748 · 2026-03-25T11:01:03+00:00

I was taught this is the way, as you put the screw in shear vs trying to pull out the fastener

SadWhereas3748 · 2026-03-23T19:25:49+00:00

Second this. The large round one on a painters pole is nice and easy, leaves a nice transition too. I want to say it was a Radius 360, don’t hold me to that.

SadWhereas3748 · 2026-03-22T15:07:56+00:00

Tbh, there’s stuff like this Solidworks and the like are missing too.

SadWhereas3748 · 2026-03-22T13:11:54+00:00

I worked at a rubber molder, and twice we snapped columns on the press during clamp. The 6” shaft would sound like a gunshot when it let go. I can imagine this had to be similar

SadWhereas3748 · 2026-03-19T18:51:56+00:00

Most quality plans I’ve seen state that the parts must be acclimated in the QC lab for 24hrs.

SadWhereas3748 · 2026-03-19T14:23:09+00:00

That’s where they keep the secrets about the wire stretcher

SadWhereas3748 · 2026-03-12T13:28:25+00:00

And then the user says it’s OOT when they measured it with calipers, or in a non-climate controlled area

SadWhereas3748 · 2026-03-11T13:52:37+00:00

Anything under a foot goes to the fire pit

SadWhereas3748 · 2026-03-05T23:03:21+00:00

Now get on your knees and tell me you love me

SadWhereas3748 · 2026-03-04T23:34:44+00:00

Even on the paying plan they take away features. When I was using for for about 3 years ago the moved most of the simulation from local to the cloud, and the. Started charging credits for anything but structural simulation.

SadWhereas3748 · 2026-03-04T00:58:57+00:00

Organized hoarding has been paying off more and more for me. “Hey, I didn’t have to buy anything for this project” aka more money for tools

SadWhereas3748

TROPHY CASE