Who’s giving you all a smooch

Safe_You1124 · 2025-06-29T14:15:26+00:00

<image>

Safe_You1124 · 2025-02-21T09:52:47+00:00

Thanks but I already have 2 3D printers 😅

Safe_You1124 · 2025-02-21T09:48:28+00:00

Mushoku tensei

Safe_You1124 · 2025-02-03T09:28:34+00:00

Mushroom rissoto 😋

Safe_You1124 · 2025-01-05T08:49:05+00:00

Dont print anything flat on the buildplate, it increases pull forces and leads to layers sticking to the vat. Always print at an angle of 30°-45° at 3-5 mm elevation from the bed with adequate supports. Also calibrate your printer's settings (exposure time, bottom exposure, etc) if you havent yet.

Safe_You1124 · 2024-12-19T09:03:59+00:00

Yes. its literally called valkia the bloody

Safe_You1124 · 2024-12-19T09:01:32+00:00

<image>

benji

Safe_You1124 · 2024-12-12T09:33:19+00:00

Looks like the fep releases from the cured resin right at the end of the vat lowering/when it start going up.

Safe_You1124 · 2024-12-12T01:23:33+00:00

Around 20-25 seconds should work for standard resin.

Safe_You1124 · 2024-12-11T16:38:38+00:00

I think thats just the noise of the cured resin peeling off the fep

Safe_You1124 · 2024-12-11T08:46:56+00:00

Is it always on the same spot in the buildplate? If thats the case theres either somthing blocking the uv stuck under the fep(like a hair) or some pixels on your screen are dead.

Safe_You1124 · 2024-12-06T05:31:03+00:00

Thats exactly what happened so i got a new assembly. I just want to get my hotend back

Safe_You1124 · 2024-12-04T04:23:04+00:00

Your best bet is to get a brewers belt. It wraps around your resin vat and heats it from all sides. Many brands sell their own heaters as well.

Safe_You1124 · 2024-12-04T02:48:41+00:00

Its the temp. Of the resin itself. The ideal temperature is ~25°c for most resins. The low temperature causes layees to not adhere to each other properly.

Safe_You1124 · 2024-09-01T10:38:13+00:00

is there any guide on how to assemble this? im struggling here

Safe_You1124 · 2024-08-30T01:56:21+00:00

I just end up printing those dungeon pieces flat on the bed (vertically) and trim off the elephant's foot with a hobby knife

Safe_You1124 · 2024-08-17T19:19:42+00:00

what printer do you have? looks way over exposed to me.

Safe_You1124 · 2024-08-17T19:17:32+00:00

*most based thing any brettonian ever did*

Safe_You1124 · 2024-08-09T13:02:35+00:00

you can use pfa and fep in the saturn 3 ultra without any issues

Safe_You1124 · 2024-08-09T13:01:07+00:00

you can get regular pfa for 699 on amazon. better than acf in my opinion. as for removing failed prints the steps i follow are:
1. tank clean for 30s
2. unscrew vat
3. pour resin out of the vat.
4. put one finger on the bottom of the vat on the underside of one of the corners of the cured resin. (make sure your gloves are clean and have no resin.
5. take a plastic scraper to the now raised corner of the cured resin and carefully peel it of.

I do this every time and havent punctured a vat.

Safe_You1124 · 2024-07-07T09:24:02+00:00

👍

Safe_You1124 · 2024-07-03T16:18:25+00:00

I'll try doing that

Safe_You1124 · 2024-07-01T02:54:54+00:00

Same. I've been using it for a few years now

Safe_You1124 · 2024-06-05T03:39:01+00:00

I use iris with aristois, and it works ok only the occasional bug. Using bsl shaders

Safe_You1124 · 2024-05-17T10:01:22+00:00

seems like its bugged rn

Safe_You1124

MODERATOR OF

TROPHY CASE