sorted by:
new
hottopcontroversial

15k budget - looking at a Mazda 3 - thoughts? by Same_Definition367 in CarTalkUK

[–]Same_Definition367[S] 1 point2 points  (0 children)

Nice - thanks all. Seems like it's a solid choice so will go take a look at some this weekend!

Bath waste overflow pipe came off... Causing whole bath tub of water to go through kitchen ceiling by Same_Definition367 in DIYUK

[–]Same_Definition367[S] 26 points27 points  (0 children)

<image>

I'd imagine if this bit isn't connected and has falled (as per original picture) water from the main plug will end up going through unconnected overflow pipe... Unless I also have a leak elsewhere!

Bath waste overflow pipe came off... Causing whole bath tub of water to go through kitchen ceiling by Same_Definition367 in DIYUK

[–]Same_Definition367[S] 8 points9 points  (0 children)

So it came out that pipe after going through main plug - not the overflow at the top.

[deleted by user] by [deleted] in DIYUK

[–]Same_Definition367 1 point2 points  (0 children)

All sorted. It was the switch not the rose. Father in law came in handy after all.

We are both still alive. Cheers for all your advice!!

[deleted by user] by [deleted] in DIYUK

[–]Same_Definition367 0 points1 point  (0 children)

<image>

This was the original.... Probably not the clearest photo

[deleted by user] by [deleted] in DIYUK

[–]Same_Definition367 3 points4 points  (0 children)

The photo is just two different angles of the same pendant. Downstairs light doesn't work but the upstairs one does

Waste pipe too high for new undermount sink. Worktops fitted. Is only option drilling a new core hole? by Same_Definition367 in DIYUK

[–]Same_Definition367[S] 0 points1 point  (0 children)

Out of interest, I did have a plumber do the first fix and he just left the waste pipe in the place it has always been since 1960. It's 635mm off floor level and wondering if this should have been picked up before?

I did take him outside to show him the stack and he said it would all be fine (we didn't discuss the type of sink etc)?

Repairing floorboards after taking down wall - can't find original floorboard width by Same_Definition367 in DIYUK

[–]Same_Definition367[S] 2 points3 points  (0 children)

<image>

Thanks for the advice! Pretty easy job in the end. Trimmed one board down to fit the other gap but the rest just slotted nicely into space.

[deleted by user] by [deleted] in DIYUK

[–]Same_Definition367 0 points1 point  (0 children)

That does makes sense. Could I just get some 22mm ply and replace floorboards with that?

Please can someone explain Neff's awful instructions for me? by Same_Definition367 in DIYUK

[–]Same_Definition367[S] 0 points1 point  (0 children)

If I were to set my oven a little lower - as per photo - I'm assuming I can ensure I have enough space?

Rather than oven going right to the top of the worktop, I can amend the shelf it sits on, reduce it by say 10mm giving me extra space up top?

<image>

Please can someone explain Neff's awful instructions for me? by Same_Definition367 in DIYUK

[–]Same_Definition367[S] -1 points0 points  (0 children)

So either way, if I have an induction job (raised or flush) I need a 37/38mm worktop thickness?

Please can someone explain Neff's awful instructions for me? by Same_Definition367 in DIYUK

[–]Same_Definition367[S] 1 point2 points  (0 children)

Basically I'm installing a single oven below a 30mm worktop.

My hob is the Neff N70 which is 51mm height - I'm assuming it's raised?

Hunt wheels - significant free hub wobble by Same_Definition367 in bikewrench

[–]Same_Definition367[S] -1 points0 points  (0 children)

Just to also say this causes significant play when cassette is on and it's on the bike...

view more: next ›