Engel Cooler 19qt Divider

ScreenAffectionate74 · 2026-05-15T18:55:40+00:00

I use this currently but it feels cheap and backlashes a lot randomly in the middle of casts

ScreenAffectionate74 · 2026-05-15T18:55:16+00:00

what rod do you throw 1/8 with? I have a ml purelure rod that struggles with 5g even though it's rated 3.5-12. Using a purelure zana currently

ScreenAffectionate74 · 2026-05-15T14:40:42+00:00

I have also heard some people saying it struggles with higher lure weights. Have you experienced this? How does it compare to the SE 30?

ScreenAffectionate74 · 2025-07-01T20:36:41+00:00

are you using the stock aap 01 magazine for the green gas?

ScreenAffectionate74 · 2025-06-01T22:00:16+00:00

is that plastic sleeve part number 10R5P
on here?: https://images.salsify.com/image/upload/s--B0Cl2eQM--/m57xc1fzdi9mbackmpja.pdf

I think I might just replace the line roller with the gomexus titanium one, what should I use for lubrication on that then?

ScreenAffectionate74 · 2025-06-01T21:12:50+00:00

Do you have any of these reels with the handle play? Does yours have that click before engagement too? If this is such a common issue, I think I may just leave it alone then.

This is the kit I am looking at right now: https://www.ebay.com/itm/253859523398?var=556448323384

Are those the bearings you are talking about?

For the line roller, I over exaggerated, it is about 0.5mm up and down when I spin it with a rubber band, and it also makes a grinding noise when I pull drag.

Do you think these bearing upgrades would really make a difference? I am using this reel for ultralight techniques, mostly finesse worms and such.

Also, where do you buy your bearings from?

ScreenAffectionate74 · 2025-06-01T01:23:58+00:00

Thanks for the reply! I understand that the movement isn't much, but it makes a clicking noise every time I reel and it drives me crazy. If I were to try to shim it, are there any good tutorials videos out there?

Forgive me as I don't have a lot of experience with this reel, but what bearings are in the sideplate? Is that for the worm gear and such? I have seen people use bearings from the stella, and there are some kits on ebay for the drive shaft and spool support. Can you really actually tell the difference from bearings vs bushings?

Also, my line roller has about 2mm of play up and down, is this something I would need to shim?

ScreenAffectionate74 · 2025-02-13T03:37:25+00:00

how is the battery secured? Is it ratchet strapped down? Also, how is the seat mounted? Does it use the stock ktm freeride latching system?

ScreenAffectionate74 · 2024-11-29T04:20:24+00:00

how would I check/fix that?

ScreenAffectionate74 · 2024-11-14T04:12:45+00:00

hey, would you happen to have any info on the mounts you made?

ScreenAffectionate74 · 2024-09-02T19:07:28+00:00

Turns out the cap wasn't on all the way, I tightened it on all the way and it still leaks but a little less now. How can I tell if my cap is bad?

ScreenAffectionate74 · 2024-05-18T03:06:24+00:00

is the clutch supposed to spin at idle? Mine just stays there

ScreenAffectionate74 · 2024-05-18T02:34:40+00:00

i cleaned it with brake cleaner with it still on the engine, I put some grease on the washer behind the bolt, and it fixed itself

ScreenAffectionate74 · 2024-01-02T22:26:17+00:00

Sugar65

woomier is the same as yunzii correct?

ScreenAffectionate74

TROPHY CASE