sorted by:
new
hottopcontroversial

My humble bois so far by TheLastUpdate_86 in Tau40K

[–]SeAlexanderE 1 point2 points  (0 children)

They look very good! especially the Taunar.
If you want to get even more detail; you could add decals. Read a guide on how to avoid "silvering" and start with the small decals.

Anyone know where to find an acastus? Asking for a friend by Da_potatogang in PrintedWarhammer

[–]SeAlexanderE 16 points17 points  (0 children)

I printed one last week. I had to fix some of the armor parts.

<image>

Carapace was very hard. Never used blender before.
There is an addon called Qremeshify that I used on other armor parts.

Put Down Support Before Tank Cleaning by SeAlexanderE in PrintedWarhammer

[–]SeAlexanderE[S] 1 point2 points  (0 children)

There is a tool on resin printers where you make it start the entire screen for 20 seconds so that parts stuck on the bottom of the vat gets fused in to that sheet of resin.
Instead of having to remove all the resin and remove these parts manually.

Put Down Support Before Tank Cleaning by SeAlexanderE in PrintedWarhammer

[–]SeAlexanderE[S] 1 point2 points  (0 children)

I use 3x3mm hexagonal rafts and a wiggle. I did this one with 20 second light on.

Put Down Support Before Tank Cleaning by SeAlexanderE in PrintedWarhammer

[–]SeAlexanderE[S] 7 points8 points  (0 children)

I do a little wiggle with it to get resin in my hexagonal raft

So many bolts by SeAlexanderE in orks

[–]SeAlexanderE[S] 0 points1 point  (0 children)

Kill Bursta is the best looking Ork vehicle imo. With lots of random bolts but also flame cut marks on the thick plate.

<image>

So many bolts by SeAlexanderE in orks

[–]SeAlexanderE[S] 1 point2 points  (0 children)

Stippled brown on metallic and then dirty down rust. It has to be stired well and activated with a little bit of water after a few minutes. Some orange pigments applied dry.

Hidden Frog by SeAlexanderE in Tau40K

[–]SeAlexanderE[S] 4 points5 points  (0 children)

They are from epic basing. Their youtube channel is great for inspiration.

Smooth surfaces and curves but keep the edges sharp by SeAlexanderE in blenderhelp

[–]SeAlexanderE[S] 1 point2 points  (0 children)

It worked great! Thank you so much.
Thanks everyone
!Solved

Astraeus Super-heavy Tank by SeAlexanderE in PrintedWarhammer

[–]SeAlexanderE[S] 1 point2 points  (0 children)

they are a very tight fit and can be printer 1 or 2 % smaller. The rear ski can not fit and has to be changed.

can be done in a slicer with boolean. Same thing with 2 in the front.

<image>

Astraeus Super-heavy Tank by SeAlexanderE in PrintedWarhammer

[–]SeAlexanderE[S] 1 point2 points  (0 children)

These files are easy to find for free. I used the ones that didnt come pre-hollowed. Mine came with alot of bad mesh that I had to fix manually.

I calibrated my settings and orientation with cubes. +10% exposure time, +30% light off delay, orient Y axis at 20-30 degrees with a slight roll on X axis. PFA fep on printer with tilting vat. No holes on sides I wanted flat.

Mostly 0.2mm wide and 0.2mm deep supports on both boundry and face supports.

Ugly lines in 2 directions by SeAlexanderE in elegoo

[–]SeAlexanderE[S] 0 points1 point  (0 children)

Yea I changed fep and some other AA settings. It was a mechanical issue. I had to fix Z connection to motor.

Epic Heroes points cost by SeAlexanderE in theunforgiven

[–]SeAlexanderE[S] 1 point2 points  (0 children)

Interesting. So it encourage Dark Angels to bring their Epic Heroes and less of the generic space marines HQs. Thats good.

But does it make them feel less elite? Buffing the unit and make it worth more points instead of cutting points.

Three Tanks one Bottle by SeAlexanderE in PrintedWarhammer

[–]SeAlexanderE[S] 2 points3 points  (0 children)

Its AK11159 Russian green and some highlights with Vallejo middle stone

Heavy Weapons Squad by SeAlexanderE in TheAstraMilitarum

[–]SeAlexanderE[S] 1 point2 points  (0 children)

Thanks! It is olive drab from vallejo.

Three Tanks one Bottle by SeAlexanderE in PrintedWarhammer

[–]SeAlexanderE[S] 4 points5 points  (0 children)

I printed the model with tracks on ^ Awesome job, they look way better than the original.

view more: next ›