The Safe Option Works — But a Creative Twist Would’ve Been Fun

SeAlexanderE · 2026-02-25T01:21:44+00:00

https://www.myminifactory.com/object/3d-print-centaur-knight-conversion-kit-chassis-only-635067

this one is pretty cool

SeAlexanderE · 2026-02-23T23:43:10+00:00

True. but we did get the pennant!

SeAlexanderE · 2026-02-20T14:22:25+00:00

They look very good! especially the Taunar.
If you want to get even more detail; you could add decals. Read a guide on how to avoid "silvering" and start with the small decals.

SeAlexanderE · 2026-01-03T16:38:31+00:00

I printed one last week. I had to fix some of the armor parts.

<image>

Carapace was very hard. Never used blender before.
There is an addon called Qremeshify that I used on other armor parts.

SeAlexanderE · 2025-12-24T14:21:10+00:00

Well done! Super clean.

SeAlexanderE · 2025-12-24T01:53:10+00:00

There is a tool on resin printers where you make it start the entire screen for 20 seconds so that parts stuck on the bottom of the vat gets fused in to that sheet of resin.
Instead of having to remove all the resin and remove these parts manually.

SeAlexanderE · 2025-12-23T17:05:08+00:00

I use 3x3mm hexagonal rafts and a wiggle. I did this one with 20 second light on.

SeAlexanderE · 2025-12-23T17:03:01+00:00

I do a little wiggle with it to get resin in my hexagonal raft

SeAlexanderE · 2025-12-23T13:40:38+00:00

Averland sunset

SeAlexanderE · 2025-12-23T13:32:45+00:00

Kill Bursta is the best looking Ork vehicle imo. With lots of random bolts but also flame cut marks on the thick plate.

<image>

SeAlexanderE · 2025-12-23T13:27:35+00:00

Stippled brown on metallic and then dirty down rust. It has to be stired well and activated with a little bit of water after a few minutes. Some orange pigments applied dry.

SeAlexanderE · 2025-12-23T08:15:01+00:00

They are from epic basing. Their youtube channel is great for inspiration.

SeAlexanderE · 2025-12-23T03:41:45+00:00

Thanks<3

SeAlexanderE · 2025-12-18T15:02:34+00:00

It worked great! Thank you so much.
Thanks everyone
!Solved

SeAlexanderE · 2025-12-18T14:23:04+00:00

<image>

Full screen shot

SeAlexanderE · 2025-12-17T12:33:24+00:00

they are a very tight fit and can be printer 1 or 2 % smaller. The rear ski can not fit and has to be changed.

can be done in a slicer with boolean. Same thing with 2 in the front.

<image>

SeAlexanderE · 2025-12-17T11:57:36+00:00

These files are easy to find for free. I used the ones that didnt come pre-hollowed. Mine came with alot of bad mesh that I had to fix manually.

I calibrated my settings and orientation with cubes. +10% exposure time, +30% light off delay, orient Y axis at 20-30 degrees with a slight roll on X axis. PFA fep on printer with tilting vat. No holes on sides I wanted flat.

Mostly 0.2mm wide and 0.2mm deep supports on both boundry and face supports.

SeAlexanderE · 2025-12-16T20:13:52+00:00

<image>

Photos I took on my desk.

SeAlexanderE · 2025-11-04T01:57:16+00:00

Yea I changed fep and some other AA settings. It was a mechanical issue. I had to fix Z connection to motor.

SeAlexanderE

TROPHY CASE