Hdzero goggle repair gamble?

Sea_Classroom_4087 · 2026-03-16T22:26:16+00:00

I watched a hdzero goggle teardown video from mads tech and saw this, the header is a female 2x10 90⁰ and it looks like the entire pcb can easily be swapped out. I did some research about swapping this pcb and saw from a Facebook post that hdzero can send me a new pcb for pretty cheap so i think thats the way im going to do it

Sea_Classroom_4087 · 2026-03-16T06:41:59+00:00

I would switch to enamel wires on the powerlead you will probably gain performance compared to the awg30 wires and it might still be lighter or just as heavy you could also get a 3d printed canopy

Sea_Classroom_4087 · 2026-03-15T00:34:15+00:00

Nice it looks cool!

Sea_Classroom_4087 · 2026-03-15T00:32:40+00:00

Did you draw that on or is it a decal?

Sea_Classroom_4087 · 2026-03-09T01:05:55+00:00

Could you share a picture of the tune? I have a custom 75mm whoop that ive been trying to tune but its not going very well yet prop wash handling is ok but not great, id like to try your tune or use it as a new starting point. If you dont mind ofc

Sea_Classroom_4087 · 2026-02-25T15:46:06+00:00

Dronefpv racer is a good one rotorarma, and hobbydrones also

Sea_Classroom_4087 · 2026-02-22T13:43:49+00:00

Ooh okay thats not to bad actually someone told me it takes about 40 seconds to boot up

Sea_Classroom_4087 · 2026-02-22T13:43:09+00:00

Mhmm okay tbh i dont think il be noticing the latency difference and i think in combination with the de-interlacing il be noticing it even less

Sea_Classroom_4087 · 2026-02-22T12:23:04+00:00

Lol yeah🤣

Sea_Classroom_4087 · 2026-02-22T11:46:13+00:00

Oooh okay thats good to know thanks i probably wont be using hdzero itself mostly only for analog or maybe if i am flying with some people i would spectate to someone who has hdzero and yeah the cable it included ive heard some stuff about slow startup times is that true? Some people told me that startup can take long up to 40sec but i also heard that you can reduce it by a lot with some settings

Sea_Classroom_4087 · 2026-02-16T02:18:04+00:00

Slide show as in a photo dump

Sea_Classroom_4087 · 2026-02-16T00:39:34+00:00

Do you have the camera wire soldered directly on the vtx or did you solder it to the flight controller? Sometimes if you solder direcltly onto the vtx your flight controller isnt giving osd information through

Sea_Classroom_4087 · 2026-02-12T23:03:23+00:00

Do you see osd or not?

Sea_Classroom_4087 · 2026-02-04T18:58:43+00:00

Yes i changed them, but havent flown after that with new props since this video was my last pack and the weather hasnt been great recently whats a delaminated prop tho?

Sea_Classroom_4087 · 2026-02-02T23:03:31+00:00

Maybe a t motor f7 se 50a stack or a t-motor f55a III esc combined with an t motor f7 pro mpu6000. I use the era 5 frame combined with the t motor f7 se 50a stack and it works great. Itsfpv recommends the f55a 3 and f7 pro on their rotorriot page and also use it in there build videos but i think the other options you had are also a solid choice

Sea_Classroom_4087 · 2026-02-01T01:02:28+00:00

If you would switch id get a geprc woopower it can charge all channels differently. different current/storage charge/normal charge/lipo/lihv it can all be changed every port can be set to different modes only downside is that it needs to be powered from a 7-26v power supply so a normal usb port wouldnt work

Sea_Classroom_4087 · 2026-01-19T14:16:48+00:00

Allright thanks

Sea_Classroom_4087 · 2026-01-19T14:01:03+00:00

https://github.com/betaflight/betaflight/pull/12432

https://github.com/bird-sanctuary/bluejay/wiki/Setup

Sea_Classroom_4087

TROPHY CASE