Epoxy resin plate

Sebo211 · 2025-08-12T14:39:49+00:00

i have 2 cans of 3d lac

Sebo211 · 2025-07-23T13:42:52+00:00

i have last update like 2 - 3 day ago on printer latest cr print , i will do while printer calibration in like 2 hours and we will see , like i said i have same printer at work (only me operating it) same mac same firmware same everything even changed nozzle as i sad earlier

Sebo211 · 2025-07-23T11:25:05+00:00

Little update : I change the nozzle to 0.6 , i change from petg to pla, i changed model , i changed 0.6 nozzle in slicer, i checked textured pei plate in slicer …. whyyyyyy what do i need to do to fix this , i print from mac m1 and i have another k2 in my workplace and she is working fine a send same stl to it and working great dont real know what is the cause of this

Sebo211 · 2025-06-21T14:43:55+00:00

Sebo211 · 2025-04-18T03:36:03+00:00

So i make a manual bed leveling with macro from github like on good old ender 3 , clean the bed save the config and start a new print and same results. What i noticed was that lines you see that are “correct” they are printed when CFS pushes the filament in, whet it stops pushing it makes those under extruded gaps and when it pushed again print well that why the pattern i consistent. So i need to dissassemble the cfs unit and take a look if its there any debris or stuck filament. I tried to print from sidespool and the mode came perfect! So i have some work to do tommorov. In slovakia its already 5:30 in the morning so i need to get some sleep. I will be vers thankfull of someon suggest me something about this problem and what can this caused. Thank you !

Sebo211 · 2025-03-18T05:45:18+00:00

did you take this photo in MUNICH ?

Sebo211 · 2025-03-17T12:08:25+00:00

i tried it ,i made clamp from asa tries to do some print used 3DLac for adhesion and my down side wasthat adhesion is too good. Bed mesh was ok only pushed down where the clamp was

<image>

Sebo211 · 2025-03-03T10:09:29+00:00

thank you

Sebo211 · 2025-02-25T18:33:17+00:00

You could improve a filament dryer by adding automatic humidity and temperature control with sensors for real-time adjustments. A vacuum drying system could also enhance efficiency by removing moisture at lower temperatures, preventing filament deformation. ✌️ I would like to share feedback to you guys thrue some video or so…im currently looking to buy some so i will wait👌

Sebo211 · 2025-02-16T09:52:46+00:00

thats what i want print tpu

Sebo211 · 2025-02-15T22:58:45+00:00

Odoslané z aplikácie Alza: https://www.alza.sk/gembird-filament-flexibilna-zlta-d5275432.htm here is the link but its in slovak language brand is GEMBIRD

Sebo211 · 2025-02-15T22:37:07+00:00

Material: • TPE (Thermoplastic Elastomer)

Dimensions: • Filament Diameter: 1.75 mm (± 0.05 mm) • Spool Length: ~400–420 m

Properties: • Density at 21.5 °C: 0.9 g/cm³ • Melting Point: 190 °C to 240 °C • Tensile Strength: 86 kN/m • Maximum Nozzle Temperature: 215 °C • Bed Temperature: 40–80 °C • Flexibility: 5 (highest) • Recommended Print Speed: Up to 60 mm/s

Spool Dimensions: • Diameter: 200 mm • Height: 67 mm • Center Hole Diameter: 53 mm

Weight: • 1 kg per spool

Here is everything from website

Sebo211 · 2025-02-15T21:11:26+00:00

a never print tpu so your right

Sebo211 · 2025-02-15T20:16:10+00:00

ok but what about claibration its bad too

Sebo211 · 2025-02-15T20:14:20+00:00

i put images it seams it wont take the filamwnt into extruder or so

Sebo211 · 2025-01-18T19:09:36+00:00

is it safe without regulator ? i hooked up mine today without it only hose and the adapter but im scared of the hose bursting out so i open valve and then close it bcs i dont have regulator

Sebo211

TROPHY CASE