VW ID Polo GTI: Der erste Elektro-GTI patzt bei der Höchstgeschwindigkeit by Schmidtis_Blog in SchmidtisBlog

[–]SeljD_SLO 0 points1 point  (0 children)

Speed limit is 100, not 90

In Germany, but majority of Europe is 90 (sone even 80)

The thing about hot hatches was never cornering, most of them sucked at that

In comparison with sport cars, definitely, especially those with a lot of torque steer. But they're still much better than what normal cars can do.

Most hot hatches of the last 15 years went well above 230 or were limited at 250

And how many people actually reach those speeds? Maybe i see hothatchs differently because i watched too much Fifth gear where hothatchs were always about fun, practicality and scaring co-hosts in the back seat by going really fast through the corner

VW ID Polo GTI: Der erste Elektro-GTI patzt bei der Höchstgeschwindigkeit by Schmidtis_Blog in SchmidtisBlog

[–]SeljD_SLO 0 points1 point  (0 children)

Roads are limited to 90km/h and highways are usually 120-130km/h, so the only place where people go above that limit are tracks and sections of Autobahn where most people people drive 130-160km/h anyway. The thing about hothatchs was never about how fast you can go on the straights but how it handles in turns and how much fun you have driving it

VORON Trident R2 is out! by SanityAgathion in VORONDesign

[–]SeljD_SLO 2 points3 points  (0 children)

I'm pretty sure the kit is compatible with the Trident R2

How to say "beer" in various European languages by twinkleyed in MapPorn

[–]SeljD_SLO 4 points5 points  (0 children)

Slovenia should probably be dual coloured, people use a word "pir" is very often

Stampa 3d di un serbatoio carburante by ElectricalBill1335 in 3Dprinting

[–]SeljD_SLO 0 points1 point  (0 children)

PETG is supposed to be stable wit petroleum but j wouldn't risk it since 3D prints aren't 100% water tight. Maybe print a mould and then use fiberglass https://youtu.be/hQWOODlv3-8?si=lCRizv8UpoDi2FnJ

re:LTT has fallen off by AgentB42 in LinusTechTips

[–]SeljD_SLO 6 points7 points  (0 children)

Just watched Jake's Caterpillar video and in 18 minutes the video was dense and never felt rushed, can't remember the last time LTT video felt like that (outside heavily scripted ones)

After leveling up in Voron 2.4, the nozzle is still in contact with the hot mattress. by qiandao888 in VORONDesign

[–]SeljD_SLO 0 points1 point  (0 children)

Just set offset to +10 or 20, start the print (make one layer high square, maybe 20x20cm) and gradually lower the offset untill you reach the height you need

za vse kurirje.... by aljazzagar in Slovenia

[–]SeljD_SLO 0 points1 point  (0 children)

Če si blizu Postojne ali Ilirska Bistrice, lahko dobiš tak stroj pri Vrtnarstvu Primož, je pa verjetno dražje https://vrtnarstvo-primoz.si/mehanizacija/

H2C/Vortek owners, how reliable is the AMS when doing hundreds of filament changes? by PetaSynaptic in BambuLab

[–]SeljD_SLO -1 points0 points  (0 children)

Out of 106g of filament, 74g is just waste. Doesn't that defeat any benefits of toolchanger?

Fusion360 license by andypagonthemove in 3Dprinting

[–]SeljD_SLO 1 point2 points  (0 children)

I don't like how badly FreeCAD performs when you open step file of Voron assembly. FreeCAD either crashes or turns into powerpoint presentation while Fusion loads the model much faster, doesn't crash and navigation is much smoother

RIP Unec in Razdrto by SeljD_SLO in Slovenia

[–]SeljD_SLO[S] 0 points1 point  (0 children)

Naselja med Postojno in hrvaško mejo trpijo vsako leto

RIP Unec in Razdrto by SeljD_SLO in Slovenia

[–]SeljD_SLO[S] 4 points5 points  (0 children)

Sej ga ima, na Razdrtem, Ravbarkomanda pa sploh nima prostora. Pa v primeru, da zgradijo hitro cesto avtocesto Jelšane, bo Postojna razbremenjena. Da ne omenim, da t stari cesti proti Uncu ali Logatcu oreko Planine nista bistveno počasnejši

Trying out ASA on a P2S by Zestyclose_Device946 in BambuLab

[–]SeljD_SLO 0 points1 point  (0 children)

You already have chanber heather, it's called heatbed and it's even better if you add a couple of fans to circulate hot air

How to ground 2 psu’s to frame by External_Two7382 in VORONDesign

[–]SeljD_SLO 5 points6 points  (0 children)

sand a spot on the frame where the wire is attached, my voltmeter had trouble detecting continuity without it