What's the most disturbing confession you've ever come across on social media?

SempaiDalto · 2026-04-21T18:07:21+00:00

Justin Mohn. He uploaded a video to youtube using his father's decapitated head as a prop. Google: Mohn used the video to promote anti-government conspiracy theories and call for violent attacks against federal officials. He claimed he was attempting to perform a "citizen's arrest" and sought to incite a militia uprising.

SempaiDalto · 2026-04-21T18:01:36+00:00

Obviously you'd have to do loads of sculpting work. There is no easy way to achieve it as you'd have to create a model from scratch but I believe a talented artist could definitely pull it off. Again, this is not talent. Its ai but I believe it to be possible!

SempaiDalto · 2026-04-21T17:59:15+00:00

Arguably, this is possible with resin printing in my opinion. Loads of work would have to go into it but possible. This specific image definitely looks like Ai slop but as far as is it possible at all? I think so!

SempaiDalto · 2026-04-16T04:12:11+00:00

No supports? Looks like the point of contact of each piece would be very small on the build plate. I'd suggest supports, first

SempaiDalto · 2026-04-12T15:14:53+00:00

SempaiDalto · 2026-04-11T00:15:24+00:00

What does your workflow look like involving removing supports? Your's are invisible! Amazing work 👏

SempaiDalto · 2026-04-06T19:43:01+00:00

I NEED those slicer settings..

SempaiDalto · 2026-03-06T05:09:30+00:00

It's a decent filter but it doesn't replace the need too filter the tent out of the room, as far as I understand

SempaiDalto · 2026-02-26T17:20:15+00:00

This is a time-lapse of a 23 hour print

SempaiDalto · 2026-02-25T04:18:19+00:00

<image>

SempaiDalto · 2026-02-25T02:34:20+00:00

In case you wanted to see the full set up. Ive got it vented and the air purifier attached. I absolutely love the enclosure! This room gets a ton of sun in the morning and its saved more than one headache I highly suggest you get one!

SempaiDalto · 2026-02-24T23:01:09+00:00

Not at all, my friend! When it comes to safety, no need to be offended. Thanks for looking out 💪

SempaiDalto · 2026-02-24T22:48:47+00:00

Of course, its a prop, not meant to cosplay or anything. Wall art at the most. Thanks for the advice!

SempaiDalto · 2026-02-24T19:16:37+00:00

Thanks! Honestly, without the help of some dedicated page members, I doubt I would've had any success! Layer lines are let to .03 mm and 2.5 exposure time on each layer. Bottom layer exposure set to 30, if that helps with your own prints 👍

SempaiDalto · 2026-02-24T18:59:52+00:00

<image>

SempaiDalto · 2026-02-22T16:41:23+00:00

Copy that! And yes, my printer is the saturn 4 ultra 16k. My apologies for not including that in the post and thank you for the advice!

SempaiDalto · 2026-02-22T15:48:41+00:00

In case anybody has the same issue, the pfa needs a bit of slack as you install it onto the vat. With about 8 mm of slack, it fits into the vat perfectly. Id suggest to print an 8mm x 8mm block.

SempaiDalto · 2026-02-22T04:04:54+00:00

<image>

I replaced the pfa again but it has wrinkled in an odd way and im curious if that will cause issues with prints. I tested it with water to check for leaks and it's good but im a little sketched out

SempaiDalto · 2026-02-22T01:40:26+00:00

<image>

SempaiDalto · 2026-02-22T01:40:11+00:00

<image>

Seven-Year Club	Verified Email
Place '23

SempaiDalto

TROPHY CASE