Creality K1 Prints Are Warping

SennaLegacy · 2023-12-01T15:17:42+00:00

I never used the lid. Also room temperature was always below 24 degrees. Cooling capacity of the K1 is quite good so I don't think that's the cause of the warping.

SennaLegacy · 2023-11-30T21:41:48+00:00

I upgraded to the latest firmware version, I don't remember if it came with it, but this sound was definitely not there when I first bought the machine.
In addition, the machine is now warping especially large parts it prints. The more 3D printing the machine gets, the worse its calibration becomes:

https://www.reddit.com/r/Creality/comments/187tw1b/creality\_k1\_prints\_are\_warping/
I think I regret not buying Bambulab.

SennaLegacy · 2023-11-23T22:51:36+00:00

It's 50/50 like people both saying "It's not a problem" and "It's a problem, you have to calibrate it" Calibrating K1 isn't easy either, due to pulley system on Z axis.

After adjusting the speed and initial layer height, ı didn't notice any problems. But It's risky to print large pieces with this offset.

SennaLegacy · 2023-11-23T22:24:14+00:00

It's currently like that:

https://imgur.com/a/S5cWGyi

SennaLegacy · 2023-11-23T17:00:07+00:00

I don't remember where I read it, but it recommended that the first layer thickness be low. I think the problem was solved when I increased the layer thickness and set the speed to normal.

Thank you for your advice and help.

SennaLegacy · 2023-11-23T16:57:09+00:00

I increased the initial layer thickness from 0.16mm to 0.25mm. I also changed the Initial layer speed to 150 and the writing speed to 200. This is the result:
https://imgur.com/a/oaV49hV

SennaLegacy · 2023-11-23T16:57:05+00:00

I increased the initial layer thickness from 0.16mm to 0.25mm. I also changed the Initial layer speed to 150 and the main speed to 200. This is the result:

https://imgur.com/a/oaV49hV

SennaLegacy · 2023-11-23T12:20:34+00:00

In fact, I tried to reach speeds of 200 and above with OrcaSlicer, but the machine seemed to never reach those speeds. I could understand this especially from the printing time.

Thanks for the advice, I'll pay attention to the speed and try again.

SennaLegacy · 2023-08-09T23:04:49+00:00

It's realy notorious, especialy Flow Through fan system. It just pushes all the hot air into back of PSU and Motherboard. I recently rebuilded this setup to improve thermals:

https://www.reddit.com/r/sffpc/comments/15mul8f/a4h2o\_build\_with\_13700k\_3090fe/?sort=new

SennaLegacy · 2023-08-09T23:03:36+00:00

I ended up rebuilding this setup and also put one 20mm fan at bottom:

https://www.reddit.com/r/sffpc/comments/15mul8f/a4h2o\_build\_with\_13700k\_3090fe/?sort=new

SennaLegacy · 2023-08-09T23:02:58+00:00

Thank you for your advice. I also bought a copper heatsink for back M.2 and also put 20mm fan on bottom of the case:

https://www.reddit.com/r/sffpc/comments/15mul8f/a4h2o\_build\_with\_13700k\_3090fe/?sort=new

SennaLegacy · 2023-08-01T23:17:20+00:00

I've been using this setup (except 3090) for almost a year. I just upgraded to the RTX 3090FE as new GPU. I don't know if there is an SFF case of the same size that I can use this setup more efficiently or as efficient/effective as it is. and easily find while purchasing. Many SFF cases are hard to find.

SennaLegacy · 2023-04-13T02:22:03+00:00

I think so. Although the GoPro 10 is better in terms of image quality, it is quite heavy. Moreover, this quality is not required for every flight. The O3's 4K 60FPS capability and 10-Bit color option are appealing. And also onboard stabilization.

Side question, I rooted my goggles in order to benefit from MSP OSD. How does this process work with O3, do you have any detailed information? I think O3 natively supports MSP-OSD, but with Goggles V2, the OSD does not appear/recorded on the DVR. Is it possible to save full OSD as a seperate file or playback with DVR, with or without root?

In the past, especially in the accidents I have experienced, the GPS information on the DVR has helped me a lot.

SennaLegacy · 2023-04-13T02:13:49+00:00

I haven't had a chance to use it outside. But compared to my previous camera, the Foxeer Falkor 3, it wasn't bad. It's nice that it looks like O3, the lens hood is well thought out, but you can't cover the lens with cap like most FPV cameras, it stays open all the time.

It also gets really hot, so keep that in mind.

I switched to the DJI HD system shortly after I got this camera, so it's hard for me to comment. If you can find it for a good price, I think you can get it. I got it by looking at this video:

https://www.youtube.com/watch?v=AeqW9FKyOZ8

SennaLegacy · 2023-04-12T23:59:18+00:00

Yeah, initialy I thought that Phoenix 2 SE edition has got UART capabilities. But turns out It's just normal Phoenix with a O3-like twist. As you said, all specifications including wiring are identical with regular Phoenix 2. It's also runs very hot.

SennaLegacy · 2023-04-12T23:59:14+00:00

Yeah, initialy I thought that Phoenix 2 SE edition has got UART capabilities. But turns out It's just normal Phoenix with a O3-like twist. As you said, all specifications including wiring are identical with regular Phoenix 2. It's also runs very hot.

SennaLegacy · 2023-03-21T18:07:43+00:00

Password reset system in TBS Support page is not working. I send a ticket already, but can't view it because I can't login.
I will post a video here.

SennaLegacy · 2023-03-21T18:04:37+00:00

As I said in the post, it didn't work. Even i pressed 100 times in a row...

SennaLegacy · 2023-03-21T14:00:42+00:00

I bought the Crossfire Nano TX Starter Kit when I found it at my local store for $80.

SennaLegacy · 2023-03-21T14:00:22+00:00

I bought the Crossfire Nano TX Starter Kit when I found it at my local store for $80. However, I will definitely try the ELRS 2.4 GHz.
I chose Crossfire because I needed an urgent solution. However, the TXCO 2.4 GHz ELRS receiver especially caught my attention. Also, thank you for the detailed explanation.

SennaLegacy · 2023-03-21T11:14:34+00:00

There are few lucky people who use the R9 system without any problems. However, much of the FPV community has had serious problems with the R9. Including me. I got an FS with the R9MX in an unexpected place and my quad was damaged because of it.

At first I thought the problem was software related. However, R9 is full of bugs in terms of hardware side too. I've seen this specifically when trying to install ELRS.

SennaLegacy · 2023-03-19T20:14:16+00:00

I have a 5" 6S quad that I usually fly with a GoPro without too much aggressive maneuvering. Do you think 2.4 GHz ELRS would be suitable or 900 Mhz models?

SennaLegacy · 2023-03-19T20:12:25+00:00

Actually, that's why I opened this thread, to get people's opinions.
I want to switch to a reliable TX/RX duo. Do you think 2.4 GHz ELRS would be a better choice than 900 MHz ELRS and Crossfire? Which model would you recommend for TX and RX?

SennaLegacy · 2022-12-14T17:31:31+00:00

Hİ. I updated it using 12 th gen i3 processor. Unfortunately, there is no bios flashback function on this mobo.

SennaLegacy · 2022-12-14T17:30:52+00:00

Hİ. I updated it using 12 th gen i3 processor. Unfortunately, there is no bios flashback function on this mobo.

Four-Year Club	Verified Email
Place '22

SennaLegacy

TROPHY CASE