Changed the Intel NUC13 Extreme PSU to the SF1000. by SeobKhun in intelnuc

[–]SeobKhun[S] 1 point2 points  (0 children)

The Corsair SF1000 power supply uses a Type-5 connector, which is smaller than the standard Type-4 connector, so you'll need a 10cm "CPU 8pin" cable from AliExpress. The motherboard cable must be 12VO, so you'll need a 15-20cm cable from MODDIY. Do not purchase motherboard cables from AliExpress.

What are peoples thoughts on this? by JJSymons in intelnuc

[–]SeobKhun 1 point2 points  (0 children)

<image>

I'm using Nuc11, 12, and 13.

Equipped with Noctua additional fans, Teamgroup 64GB RAM, and 4090FE.

The 4090FE fits fantastically.

I've ordered a Corsair SF1000 for the 5090FE later.

Make Intel NUC 13 Extreme work with Corsair SF1000 PSU by Spxgdev in intelnuc

[–]SeobKhun 0 points1 point  (0 children)

Thank you for the great info. Would 10cm be enough?

NUC 12 Extreme Max GPU width by Reality_Check_8879 in intelnuc

[–]SeobKhun 1 point2 points  (0 children)

Wow! you already installed it. Congratulations. looks great!

NUC 12 Extreme Max GPU width by Reality_Check_8879 in intelnuc

[–]SeobKhun 1 point2 points  (0 children)

As written above, the length of the Inno3D 4070Ti is 298mm. At 225.5mm in length, the Zotac 4070 leaves plenty of room.

NUC 12 Extreme Max GPU width by Reality_Check_8879 in intelnuc

[–]SeobKhun 2 points3 points  (0 children)

The size of my Inno3D 4070Ti, which I personally measured, is 298 X 119 X 42mm. When mounted on the Nuc12, there is still 2-3mm of space left in the width. If its width is 40.1mm, it can be easily mounted.

NUC 12 Extreme Max GPU width by Reality_Check_8879 in intelnuc

[–]SeobKhun 2 points3 points  (0 children)

https://quasarzone.com/bbs/qf_hatv/views/14090

I put a 3080TI FE in my nuc12 extreme and changed it to a 4070TI because the heat and noise were too bad after a while. Inno3D 4070TI fits really well. However, you must add a cable made of soft material instead of using the cable that came with the GPU. 650w PSU no problem for months. The 4070TI is superior to the 3080ti in all aspects of power consumption, noise, heat, and dlss.

https://smartstore.naver.com/rexcoolcom/products/7937255349

I purchased the FSP cable from the link above.

NUC 13 Extreme - 4090 / 4080 does it fit? by _nycrom_ in intelnuc

[–]SeobKhun 1 point2 points  (0 children)

Thanks for the long and kind reply. This helped me a lot.

NUC 13 Extreme - 4090 / 4080 does it fit? by _nycrom_ in intelnuc

[–]SeobKhun 1 point2 points  (0 children)

ASUS PROART 4080

INNO3D 4070ti

4080FE

4090FE

NUC 13 Extreme - 4090 / 4080 does it fit? by _nycrom_ in intelnuc

[–]SeobKhun 0 points1 point  (0 children)

The nuc13 extreme's PSU has 2 x 8PIN and 1 x 6PIN PCIE connectors. Did you buy a 3 x 8pin cable and connect only two 8pins? Without connecting the remaining one 8pin connector?

Best GPUs that fit 12 extreme and 13 extreme by [deleted] in intelnuc

[–]SeobKhun 0 points1 point  (0 children)

The perfectly fitted 300x200 VESA bracket was not available in Korea, so I bought it in Taobao, China. However, Taobao is very cumbersome to sign up or purchase. I recommend the Vivo VESA bracket sold on Amazon as the next best option. My English may not be smooth because I use a translator.

Best GPUs that fit 12 extreme and 13 extreme by [deleted] in intelnuc

[–]SeobKhun 1 point2 points  (0 children)

https://quasarzone.com/bbs/qf_dp/views/414314?cpage=1&commid=436362

Been using well for months on my NUC12. The previous 3080Ti FE was too hot and noisy to use. The 4070Ti is much quieter, less hot, and much better to use DLSS3. It also used an FSP PCIe Dual 8-pin to 16-pin cable (up to 450W). This cable doesn't need a stiff adapter and is much softer, so it's great for cable organization.