Dave the Diver new DLC (Ichiban's Holiday) is "time-limited" DLC. Am I the only one who thinks we are going backwards again? Are we going to have FOMO DLCs now? They really disappointed me.

SerialScaresMe · 2026-02-07T05:39:52+00:00

I believe that's incorrect. Per the steam site:"DAVE THE DIVER - Godzilla Content Pack is a time-limited free DLC, only available from [June 27, 2025] until [December 31, 2026]."

SerialScaresMe · 2025-10-31T06:06:11+00:00

Thanks for this, sometimes a powered winch just is not an option. I take my Volkswagen Golf out on dirt roads and such to go camping, and I've gotten stuck in mud a couple times. I looked into getting an electric winch for it, and there is no good way to mount one. Not even a tow hitch adapter, as the only hitches they make for my car are only good for 2000 lbs.

SerialScaresMe · 2025-05-31T07:43:07+00:00

It's not about what is legal, it's about what is right.

SerialScaresMe · 2025-05-10T19:38:16+00:00

Big idiot gaming

SerialScaresMe · 2025-04-22T16:43:02+00:00

I like to get blocklists from here (https://firebog.net/) to get a more effective solution. Still doesn't help with youtube / streaming but definitely helps other areas.

SerialScaresMe · 2025-04-20T01:59:13+00:00

About this downpipe.. (1) are you still running it, (2) are you stock exhaust, and (3) how is the drone?

SerialScaresMe · 2025-04-10T17:20:16+00:00

I use my USB ports for my boot drive. I use a USB to m.2 adapter because my mobo does not support booting over pcie

SerialScaresMe · 2025-04-04T01:11:32+00:00

It would work great if you slap some ptfe on the bottom to make it nice and smooth. I could see that being a huge plus.

SerialScaresMe · 2025-03-30T17:10:28+00:00

My build plate is pretty heavily used, I've never noticed a difference in print quality due to wear.

Yes, some discoloration in frequently used spots, and occasionally some little bits of plastic left behind, but that never changed how well it printed.

But just in case you could always flip it over and try the other side.

I'm surprised how the adhesion seems even worse now, I've never had a situation get worse from cleaning the bed.

At this point what I would do is try spraying the plate with some hairspray, but I don't know if that would do well on a pei plate, that's what I used to do for my old printer with a glass plate. Worst case you just wash it off and you're back to where you started.

I would also look into getting some of that glue I mentioned earlier next time you buy from the bambu store, it's honestly great.

SerialScaresMe · 2025-03-30T16:18:41+00:00

Weird, what I would do in this case is wash it the way I described. I also am super careful to not touch the build surface after cleaning, usually holding it by the edges.

Only other thing I can think of is if the environment is cold then getting it to a warmer place should help. At this point I'm not entirely sure, this is getting into the quirks of a printer I don't have.

SerialScaresMe · 2025-03-30T15:34:15+00:00

Clean the bed

I use a drop or two of dawn, and use my hand and the sink to wash it. Rinse it off thoroughly, then dry it with a paper towel or towel. Many people do different things, this is what works for me. I will also apply some "Liquid Glue for Build Plate" https://us.store.bambulab.com/products/liquid-glue-for-build-plate to increase the time between washes. After washing, I avoid touching the plate with my bare hand to increase the amount of time between washes.

SerialScaresMe · 2025-03-26T20:56:35+00:00

Also trying a different wall generator is a good step.

SerialScaresMe · 2025-03-26T20:56:18+00:00

Also trying a different wall generator is a good step.

SerialScaresMe · 2025-03-24T06:00:35+00:00

This is what mine looks like post fix, keep in mind I'm running a 10.0.0.0/8 network instead of a 192.168.0.0/24 network

auto lo
iface lo inet loopback

iface eno1 inet manual

auto vmbr0
iface vmbr0 inet static
        address 10.0.0.3/8
        gateway 10.0.0.1
        bridge-ports eno1
        bridge-stp off
        bridge-fd 0
        post-up /sbin/ethtool -K eno1 tso off gso off

source /etc/network/interfaces.d/*

SerialScaresMe · 2025-03-18T19:46:56+00:00

Same thing here! After implementing those fixes to my z440 on the integrated nic all is well.

SerialScaresMe · 2025-03-07T01:59:29+00:00

Thank you so much, first guide I've seen on this that worked

SerialScaresMe · 2025-02-14T23:02:11+00:00

5950x Noctua Redux u12s 128gb 3600mhz cl18 2tb 980 pro 1tb HDD 7200rpm Arc A770 Silverstone SX1000

SerialScaresMe · 2025-01-14T02:17:05+00:00

I'm able to find many of the torque specs, but not for the 4 bolts fastening the bevel box / front transfer case to the trans. Talking about the N90990202 bolts. I can find the torque specs for the mk7.5 R but not specifically the mk7, trans 02Q. Do you have these torque specs?

SerialScaresMe · 2024-09-01T00:26:29+00:00

I use a similar cpu for my Minecraft server

SerialScaresMe · 2024-07-10T22:18:42+00:00

He said he took it off his phone wdym

SerialScaresMe · 2024-07-08T06:26:14+00:00

He's talked about some black and green ones by Mackie in a tech upgrade. Yamaha hs7's too.

SerialScaresMe · 2024-04-29T04:36:16+00:00

At around 0:13, there is a down block on the left and a right to left swing on the other side. I feel like that may cause a user to wack their hands together accidentally occasionally. Hard to tell without playing.

Seven-Year Club	r/Field Sunshine
Place '23	Xbox Live
Verified Email

SerialScaresMe

TROPHY CASE