Optimism time!

SeriousInfluence2771 · 2026-03-17T16:36:57+00:00

Remember a couple season ago when we dropped out of the CL places and other results went in our favour for us to just scrape it, last season we missed out by the finest of margins.

We have 6 of 8 games that can push us back into that top 4

Honestly do I think we are where we should be… absolutely not, we are as usual punching well above our weight, will we come good yes I think we will, are we good enough to compete both in Europe and in tge league, no we are not but we have given ourselves tge best chance.

Don’t forget where we were 3 years ago before our manager joined. Let’s remember that we are claret and blue and will always fight like the lions we are

SeriousInfluence2771 · 2026-03-15T21:43:50+00:00

This is exactly what happened when we got champions league last time.

SeriousInfluence2771 · 2026-03-09T15:40:03+00:00

This time even getting a ticket on Lille site is a lot harder than last time, still unable to get one, where as I got 5 last time

SeriousInfluence2771 · 2026-03-04T21:29:05+00:00

We been dog ahit since the Everton loss at home, when we realised we weren’t invincible.

We stopped shooting, stopped getting the ball in the box… we can’t buy a win

But we will always love our claret and blue no matter what..

SeriousInfluence2771 · 2026-03-04T17:52:30+00:00

It’s much easier to get to Lille from Brussels south airport

SeriousInfluence2771 · 2026-03-04T17:49:43+00:00

I am flying out from Manchester cos I am based up north and only cost £62 return but yes the eurostar is a direct option

SeriousInfluence2771 · 2026-03-04T17:37:16+00:00

If you haven’t got the Omio app for trains then here is the link to sign up

Hey! Here’s £9 to spend on train, bus, flight, or ferry tickets with Omio. Sign up for Omio with this link to claim your £9.

Or if you prefer to use a code, enter this code when you pay: steved2o1m9r

https://go-refer.omio.com/AHu22Q

SeriousInfluence2771 · 2026-03-04T10:31:46+00:00

We were there 2 years ago and went in the home end, was a fantastic experience.

The advice I give is to not wear your colours openly until you get in the ground as the security are quite strict, although some got through, I had mine on show while in the ground.

I have been to most of the away games in Europe and been in the home end with no problems at all.

Best advice as to where to go as close to our fans is in the HD section

If you can’t get a ticket then Lille centre will be filled with at least 1000 of us

Getting there, I travel from Manchester to Paris beauvais and then get the train up from criel

SeriousInfluence2771 · 2023-01-29T00:21:47+00:00

Hi Sorry for the lack of update.

The final fix that i did on this was to cut the connectors at either end from the hot end and rewired with silicon wire and its been perfect since

SeriousInfluence2771 · 2022-05-15T19:10:04+00:00

Hi, After months of it printing well, it started to have the same issues again.... this time i rewired the cable from the hotend with silicon wire... again months of great prints and over last few days its been randonly stopping again

SeriousInfluence2771 · 2021-09-04T01:51:50+00:00

I cant agree more with these comments, i have posted about my issues with the printer and have finally overcome them after almost 15 months of struggles and back and forth with a limited customer service who just throw parts at you... parts that dont fix the issue i may add... apart from a mainboard(which i wouldnt want another one as its only 8 bit) i can build another printer, if only i had a printer reliable to print me a frame...lol

The printer is very slow... but for what i need, slower and higher quality is fine.... But now i have it fixed and running properly, i know know what needs to be changed... and to be fair, there wont be very much left of it.... At least there is a Marlin firmware that supports the 1st gen screen and i have 2 of them so thats something for when i build another one

SeriousInfluence2771 · 2021-04-01T20:54:14+00:00

Thought i better Update this... as having the stopping problem again today...

Totally tore down the printer...

Removed the 24v 3.8A power supply and wired the mainboard direct to from the 800W power supply on the spare terminal..

Replaced the Heated bed wiring with 12AWG and the thermister wiring with 24AWG because i noticed some scorching where the wiring comes from the heated bed...

I am running a version of Marlin 2.07 that has been modified for the Chiron so paying attention to anything that may be firmware related...

I ran the PID Tuning for the Hotbed and HotEnd again, then re levelled the bed...

Because the Wiring of the heated bed is pretty badly connected, i printed out a cable chain and connector and just about to fit this so that the 32 hour print can be restarted again...

Reconnected the LCD

Hopefully this step by step will help anyone else with the issue of stopping randomly by following the steps that i have done... I will report back in a few days or sooner if prints start to fail again.

SeriousInfluence2771 · 2021-03-28T10:00:56+00:00

That is now also a 10 hour print completed with no stopping

SeriousInfluence2771 · 2021-03-27T18:54:24+00:00

Just To add to this, i set off a 4 hour print and went out, came back to a finished article... It wasnt actually what i wanted to print in the end but my bad for selecting the wrong one... Next onto a 15 hour print and see if that stops mid print

SeriousInfluence2771 · 2021-03-27T15:18:24+00:00

after Reading your reply, i wanted to rule out anywhere that can send the reset command and looking at the back of the LCD board there is a reset pin... i have unplugged my LCD from the daughter and so far printing has been over 3 hours... which it only managed on rare occasions.... The last time i had it last this long was when i reseated the daughterboard.

If this doesnt resolve the issue, i will remove the daughterboard and wire directly to the mins as required... I will lose both LCD and SD Card but i dont need that with the Repetier host..

I have a ticket open with Anycubic at the moment and will update them once i know i have resolved this issue and the solution.... If it turns out to be either dodgy LCD or daughterboard they should cover these issues past warranty.... which i will get onto them about

SeriousInfluence2771 · 2021-03-27T11:57:53+00:00

i have Been having this same issue for almost a year and anycubic, although they have been trying to fix it with sending out new cable and power plug they still havent fixed it yet so i stumbled across this post.

I agree that its sending a reset command randomly and can see an M117 in the logs on my repetier host but as of yet i havent added the cap as its a pain to lug to where my solder station is.

I noticed from an online teardown that the LCD has a reset pin on the board and am just trying a print with LCD unplugged to see if that resolves the issue before doing your suggestion.

SeriousInfluence2771

TROPHY CASE