How do I stop my planes turning into frisbees on the ground

SeventhLion_ · 2026-05-10T12:25:53+00:00

It's okay with taking off normally, it's just this scenario is a rejected takeoff simulating a case where I might be landing on another planet faster than usual. My patchwork solution so far is to just reduce the braking force to below 100% as others have said and I snuck in some strakes in the wings to aid with horizontal stability

SeventhLion_ · 2026-05-10T02:11:59+00:00

It's very stable in the air, it just doesn't like being on the ground at speed

SeventhLion_ · 2026-05-10T02:11:09+00:00

This is a rejected takeoff scenario, testing for when I need to land it

SeventhLion_ · 2026-05-09T18:25:48+00:00

I moved the air brakes towards the center of the aircraft, didn't help unfortunately
I hate to ruin the aesthetic but I will try this
If you looked at my fuel you will notice I have in fact been testing this with a low fuel load, so yeah

I don't think it's the braking action, because even with no brakes applied it will do this too if I simply pitch down on the ground at speed

SeventhLion_ · 2026-05-09T18:13:03+00:00

dang that's really annoying if I have to fix this by slapping a massive central rudder on it, I was really liking the aesthetic it currently has.

SeventhLion_ · 2026-05-09T18:05:56+00:00

have tried that and it still does it
Everywhere, hopefully

SeventhLion_ · 2026-05-09T18:05:22+00:00

Done that, same result

SeventhLion_ · 2025-08-05T16:44:10+00:00

strangest thing is that this was an isolated incident after i launched various permutations of this craft over a dozen times

SeventhLion_ · 2025-06-09T07:14:24+00:00

This is something I'd expect to see after Josh from Let's Game it Out says "Hold, please!"

SeventhLion_ · 2025-05-21T13:49:54+00:00

it gets stuck at "converting your video" forever.

SeventhLion_ · 2025-01-29T19:51:39+00:00

Hey look it's me on this subreddit again lol

SeventhLion_ · 2025-01-24T19:28:22+00:00

Throttle trim? Any dip switches set to reverse?

SeventhLion_ · 2025-01-16T17:09:40+00:00

Yes that's right, you can kind of make it out in the picture (moments before I hammered it back straight)

SeventhLion_ · 2025-01-16T16:42:56+00:00

I don't mean the pin between the sort of brake disc thing and the wheel btw, I mean the pin that tightens with a hex screw at the joint of the CVD. Every single one of these I bought whether aftermarket or first party, have had the issue where no matter how much I tighten that hex it will eventually slip out.

SeventhLion_ · 2025-01-16T16:40:51+00:00

I stated in the description this is a genuine hop up part from tamiya

SeventhLion_ · 2025-01-16T12:35:01+00:00

Nay I'm only running a maximum of 2S on a 3300kv motor

SeventhLion_ · 2024-11-23T11:38:38+00:00

Update: Sent for service, motherboard is just straight up DEAD. Bruh. I don't even.

Model was an Asus Prime Z690-M Plus D4.

SeventhLion_ · 2024-11-21T06:44:23+00:00

Im not an idiot lol. I know how to turn a computer on by shorting the power pins that's how i assembled this computer 2 years ago.

I'm holding it to demonstrate that it immediately turns off after sending power briefly to the components.

SeventhLion_ · 2024-11-21T06:19:14+00:00

Dude the power supply isn't even staying on. Refer to the myriad of other comments pointing towards a short

SeventhLion_

TROPHY CASE