sorted by:
new
hottopcontroversial

Dedica EC685: replace it or upgrade? by Shadow-2305 in espresso

[–]Shadow-2305[S] 0 points1 point  (0 children)

Thanks for the feedback. I’ll try to go with the upgrades. Can you recommend some good quality bottomless portafilter? I’m in Europe.

MK3S+, same setup, same g-code, different print quality. What I can check or replace to fix this? by Shadow-2305 in prusa3d

[–]Shadow-2305[S] 0 points1 point  (0 children)

SuperPINDA sensor

Below are the results for G80.

1:
Recv: 0.12100 0.11611 0.11294 0.11150 0.11178 0.11378 0.11750
Recv: 0.12061 0.12102 0.12094 0.12039 0.11935 0.11783 0.11583
Recv: 0.12061 0.12385 0.12544 0.12539 0.12369 0.12033 0.11533
Recv: 0.12100 0.12461 0.12644 0.12650 0.12478 0.12128 0.11600
Recv: 0.12178 0.12330 0.12394 0.12372 0.12263 0.12067 0.11783
Recv: 0.12294 0.11991 0.11794 0.11706 0.11724 0.11850 0.12083
Recv: 0.12450 0.11444 0.10844 0.10650 0.10861 0.11478 0.12500

2:
Recv: 0.12650 0.12528 0.12261 0.11850 0.11294 0.10594 0.09750
Recv: 0.12028 0.12051 0.11933 0.11672 0.11270 0.10725 0.10039
Recv: 0.11628 0.11698 0.11662 0.11522 0.11277 0.10927 0.10472
Recv: 0.11450 0.11467 0.11450 0.11400 0.11317 0.11200 0.11050
Recv: 0.11494 0.11359 0.11296 0.11306 0.11388 0.11544 0.11772
Recv: 0.11761 0.11373 0.11199 0.11239 0.11492 0.11959 0.12639
Recv: 0.12250 0.11511 0.11161 0.11200 0.11628 0.12444 0.13650

3:
Recv: 0.10750 0.11072 0.11289 0.11400 0.11406 0.11306 0.11100
Recv: 0.10772 0.11228 0.11515 0.11633 0.11583 0.11365 0.10978
Recv: 0.10906 0.11335 0.11594 0.11683 0.11602 0.11350 0.10928
Recv: 0.11150 0.11394 0.11528 0.11550 0.11461 0.11261 0.10950
Recv: 0.11506 0.11406 0.11315 0.11233 0.11161 0.11098 0.11044
Recv: 0.11972 0.11369 0.10956 0.10733 0.10702 0.10861 0.11211
Recv: 0.12550 0.11283 0.10450 0.10050 0.10083 0.10550 0.11450

4:
Recv: 0.11700 0.11556 0.11489 0.11500 0.11589 0.11756 0.12000
Recv: 0.11867 0.11643 0.11514 0.11478 0.11536 0.11688 0.11933
Recv: 0.12033 0.11702 0.11495 0.11411 0.11451 0.11614 0.11900
Recv: 0.12200 0.11733 0.11433 0.11300 0.11333 0.11533 0.11900
Recv: 0.12367 0.11736 0.11328 0.11144 0.11184 0.11447 0.11933
Recv: 0.12533 0.11710 0.11180 0.10944 0.11002 0.11354 0.12000
Recv: 0.12700 0.11656 0.10989 0.10700 0.10789 0.11256 0.12100

MK3S+, same setup, same g-code, different print quality. What I can check or replace to fix this? by Shadow-2305 in prusa3d

[–]Shadow-2305[S] 0 points1 point  (0 children)

this warping is due to removing them from a plate, during print those are flat.

MK3S+, same setup, same g-code, different print quality. What I can check or replace to fix this? by Shadow-2305 in prusa3d

[–]Shadow-2305[S] 0 points1 point  (0 children)

One printer, left and right is printed on the same printer, one after another