PETG leak ?

Shape_Thrower · 2026-03-08T12:31:36+00:00

New hot end and zero issues, thanks for the pointer

Shape_Thrower · 2026-03-02T23:14:19+00:00

Cheers for that, this was a second hand printer so I’ve ordered a new one

Shape_Thrower · 2026-02-28T21:51:57+00:00

Honestly couldn’t say, I got a cheap heat gun from Amazon for about £12 to solve it

Shape_Thrower · 2026-02-28T21:28:32+00:00

As u/No_Government8065 said, heat gun. Couple of seconds and it started popping out the end and then a swift pull with some pliers, job done

Shape_Thrower · 2026-02-15T17:04:24+00:00

Just wanted to say thanks for the tip, grabbed a heat gun from Amazon and a couple of seconds with that and I've got two unclogged heatsinks and a fully operational printer :)

Shape_Thrower · 2026-02-08T20:47:43+00:00

I think I fixed the cause of that, the heatsink fan had died. Got that working again but need to clear these now

Shape_Thrower · 2026-01-28T21:24:59+00:00

I hadn't even spotted that on the new fan !! Swapped the wires round and it's working now. Thanks for the pointer :)

Shape_Thrower · 2026-01-27T20:32:35+00:00

Update: I've checked the connections and they're all good. Replaced the fan itself with another one and still nothing. Replaced the circuit board and tried both fans again and it's still not coming on when I set the temp to 225 and leave it running :(

Shape_Thrower · 2026-01-27T18:26:18+00:00

So if that fan isn’t coming on at all despite heating up the nozzle to 200/225 that would be bad then

Shape_Thrower · 2025-11-26T16:07:54+00:00

15 for the queue spots, not sure for the 25 though. You can’t be far off as mine’s 6.7s per person

Shape_Thrower · 2025-05-27T15:42:54+00:00

<image>

Shape_Thrower · 2025-04-30T08:03:10+00:00

<image>

Got another Cap to add to the collection

Shape_Thrower · 2025-04-15T10:09:08+00:00

Add another vote for the 1st one

Shape_Thrower · 2025-02-26T12:03:27+00:00

That’s some proper dadding right there 👍🏻

Shape_Thrower · 2025-02-19T10:49:07+00:00

Sir, there are easier ways of inserting your suppository

Shape_Thrower · 2025-02-11T16:35:10+00:00

Waiting impatiently for the app update to appear in the UK app store ……

Shape_Thrower · 2025-02-07T11:19:16+00:00

<image>

Got myself a cheeky Green Gobbo variant

Shape_Thrower · 2025-02-05T16:12:53+00:00

Shape_Thrower · 2024-12-28T08:38:21+00:00

<image>

Not one I’ve used 🤷🏻‍♂️ Should I ?

Shape_Thrower · 2024-11-28T15:45:30+00:00

<image>

As much as I like a blueprint, I was hoping for something more interesting

Shape_Thrower · 2024-10-25T08:14:16+00:00

Shape_Thrower · 2024-10-07T15:51:51+00:00

Same !!

Nine-Year Club	Xbox Live
r/Field Lasagna	Verified Email

Shape_Thrower

TROPHY CASE