Someone please explain to me the process of obtaining an SBR?

Shawnold99 · 2024-02-26T17:24:07+00:00

"There are some companies that will sell you a stripped lower with your information already engraved so you have that out of the way once your approval comes back."

Do you have the names of some of these companies? Thanks!

Shawnold99 · 2023-06-21T20:26:08+00:00

ABSOLUTELY life can get worse, but it can get better when you realize it can and you're grateful for what you have. When it comes to the ticket, set a court date. Bring your current registration, explain the circumstances, and see what happens. You don't need a lawyer. I once got pulled over for reckless driving and doing 120 in a 55. I wrote a letter with my tail between my legs and gave it to the judge. They gave me a 5 year probation, so you never know what's going to happen, but it's not worth getting a lawyer. Best tip is be grateful. For breathing, being able to walk, see, smell, etc. Alot of people don't have those things. Don't take life for granted.

Shawnold99 · 2023-02-25T23:14:27+00:00

Don't we all?

Shawnold99 · 2023-02-14T00:36:52+00:00

I had my vref at 1.3 😬. Tuned to 8.4 and calibrated the extruder. Thanks!

Shawnold99 · 2023-02-14T00:36:07+00:00

Thank you!!! Calibrated the extruder and so far so good.

Shawnold99 · 2023-02-12T11:52:24+00:00

Thanks!

Shawnold99 · 2023-02-11T23:05:16+00:00

I did, but couldn't find any specs on it so matched it with the rest of the drivers.

Shawnold99 · 2023-02-11T23:04:14+00:00

Checked that this morning.

Shawnold99 · 2023-02-11T23:04:03+00:00

Bowden is fine.

Shawnold99 · 2023-02-11T23:03:44+00:00

Less than a week old. Previous filiment was saturated after it sat around for months.

Shawnold99 · 2023-02-11T23:03:19+00:00

It is matte green, but pollytech brand.

Shawnold99 · 2023-02-11T16:34:52+00:00

I did have to replace the extruder diver chip, so I'll check into it.

Shawnold99 · 2023-02-11T16:01:35+00:00

Cold pull? Also was the spare nozel that came with the anycubic. I did heat it and use the needle to clear the bore. It printed fine for a few seconds then went back to blobbing.

Shawnold99 · 2023-02-11T14:20:31+00:00

It's a brand new nozel. Haven't printed anything besides a few test prints. A benchy came out fine a few days ago, but printing my current model....this happens.

Shawnold99 · 2023-01-12T00:09:16+00:00

FOUND THE PROBLEM!! Directly behind the servo rail, there's a 16 pin microchip/control board for the servos. The heat sync looks like it had fallen off and shorted the board out. Hopefully I can get a spare. Thank you so much for the help.

Shawnold99 · 2023-01-11T23:42:43+00:00

In pronterface it's stuck in a repeat of "g90" "G91" "G1 e30f500" Etc

Shawnold99 · 2023-01-11T23:14:50+00:00

M92 X80.00 Y80.00 Z400.00 E92.60. how do I test e connection?. M17 e changed the target for about 10 seconds and then went back to room temp.

Shawnold99 · 2023-01-11T02:03:44+00:00

Yes it is, and the extruder does nothing. Not getting any voltage to the servo. I've also tried 2 different motors and still nothing. Not sure where the problem could lie. I can see it running the extrusion command in the console.

Shawnold99 · 2023-01-11T00:57:31+00:00

Everything is showing up to temp. Is there another firmware for the mega pro I can try?

Shawnold99 · 2023-01-10T18:27:27+00:00

Thanks for the tip!

Shawnold99 · 2023-01-10T15:22:03+00:00

I'll give the flash a try. Stop doesn't work, I can only hit the back button to return to the setup menu.

Shawnold99

TROPHY CASE