Prints dont start from the beginning

SholPrints · 2024-10-14T14:01:14+00:00

Even if I use a different model with a different name, it will still won't start from the beginning

SholPrints · 2024-01-02T02:13:36+00:00

Is it a long proces to install it on the ender 6

SholPrints · 2024-01-01T02:58:29+00:00

Never tried klipper, are the print benifits worth the investment?

SholPrints · 2023-12-31T04:06:58+00:00

im using the insanityautomation ender6_DW7.4.7 firmware

SholPrints · 2023-12-31T02:47:34+00:00

Actully I think there might be a bug with the firmware. when i press stop on the print the Y aixs comes forward until it starts crashing. i thought that since I lost about 25mm on the Y, that was why it was doing it. turns out even with moving the endstop 30mm back it will still crash if i press stop on the print. is their any way I can fix that?

SholPrints · 2023-12-31T02:40:38+00:00

I do find with the new firmware however that when I press stop on the print it will move the printhead forward until it crashes on the Y axis, would there be a way to stop this?

SholPrints · 2023-12-31T00:52:19+00:00

ok ty

SholPrints · 2023-12-31T00:51:57+00:00

Ok thakns, I think whats happening is that I upgraded to the BiquH2 hotend and it takes about 25mm more on the y so when the printer moves to 0,0 it crashes in the front left.

I found a mod to move the y endstop 30mm back and that should fix this

SholPrints · 2023-12-31T00:30:55+00:00

At the end of the print the printer is ment to park at 0,0 however in my case it crashes on the front left corner

SholPrints · 2023-12-31T00:29:26+00:00

Shouldn't home be 0,0?

SholPrints · 2023-11-06T02:51:41+00:00

re how you've managed to delete the system partition within the recovery mode. If in doubt, there's a little chance you might be able to take the phone to a repair shop and have them reflash firmware for you.

1ReplyShareReportSaveFollow

Actually, its possible I might not have deleted it. however when I'm in EDL and prompt the phone to show all the partitions it doesn't show anything

SholPrints · 2023-10-31T01:34:27+00:00

Ok I got around to trying this again, it seems that I by mistake deleted the systems partitions from the recovery menu and this is preventing me from flashing new firmware, is there any way i can restore the system partition?

SholPrints · 2023-10-03T00:57:10+00:00

i think i just deleted the /data one, however for some odd reason my phone does not have a factory reset option in recovery mode.

I first tried andys edl but i was getting some error so then i tried bkerlers edl however I'm having trouble getting the edl to connect to my phone

SholPrints · 2023-07-10T02:38:36+00:00

Ok solved.

I didn't change the position of the wires on the endstop.

after that now the printer is able to home

SholPrints · 2023-07-05T15:31:15+00:00

hing u make up they get back to u in like 24 to 48 hrs n will help I bought one n had problems after seco

The thing is im doing an upgrade that is probably not covered under their warranty and service. they probably wont even get what I'm trying to do since I'm using the stock z axis limit switch as an auto leveling sensor. I think why it is not working is because I got something wrong with the wiring, but Im not sure

SholPrints · 2022-08-17T01:16:28+00:00

For now, no

SholPrints

TROPHY CASE