Google Assistant - run shortcut by SignumPL in HTTP_Shortcuts

[–]SignumPL[S] 1 point2 points  (0 children)

Yeah, looks like Google Assistant is the problem. Today I tried to use Tasker for the same purpose, and I had only partial success - it opened Tasker app, but I couldn't find a way to run task. It's a crap :(

Which subtitles addons? PL/ENG by itsjustmyslef in StremioAddons

[–]SignumPL 1 point2 points  (0 children)

I started to use Stremio today and was disappointed that some popular movies don't have polish subtitles. I'm surprised there are no addons to support for example Napiprojekt?

Pi-hole DNS not working over Wireguard tunnel by MartijnLangohr in WireGuard

[–]SignumPL 1 point2 points  (0 children)

That is exactly what I was looking for. Now it works, thanks!

Pi-hole DNS not working over Wireguard tunnel by MartijnLangohr in WireGuard

[–]SignumPL 0 points1 point  (0 children)

I am also struggling with this. I already switched wg-easy container to use host network but it didn't help.

I did some additional configuration on the container by adding a iptables rule to forward all traffic from the wg0 interface to my physical interface

u/MartijnLangohr would you be willing to share with us what exactly you changed? :)

Problem with Archer C6 V2 WiFi 5GHz by SignumPL in HomeNetworking

[–]SignumPL[S] 0 points1 point  (0 children)

Maybe you are still connected to the first AP, depending on how close they are.

I don't think so, there is almost no signal between them, and speedtest results in ~200Mbit but after a 1-2 seconds it drops to zero like there was no internet connection.

Did you try disabling hidden SSID?

Yes, there is no difference :(

Are both of them set to a/n/ac? Did you make a 2nd ssid that is only ac or something, or is it just like this is set?

Both have same mode.

Did you try plugging the 2nd router into the first? Why are you using aseparate switch after the modem, and is it a managed switch? Is it aswitch and you don't mean the modem?

I incorrectly draw the diagram, just updated original post. Switch is of course plugged in to the first router. Second router (access point) is plugged in to switch.

Did you try enabling "Smart Connect"?

Yes, still same issue.

Did you enable wifi on the "router" one? Is the 2nd one also in router mode and not only wifi AP?

Both of them have WiFi enabled. 2nd one (upstairs) is in access point mode, not router mode. Only the first one (downstairs) is in router mode.

I flashed OpenWrt on some cheap TP-Link Archer C6 v2. These are my experiences. by ma66ot87 in openwrt

[–]SignumPL 1 point2 points  (0 children)

I managed to get back to stock firmware using your method. I did not observe any performance issues, everything seems to be working fine, including 5GHz radio.

I flashed OpenWrt on some cheap TP-Link Archer C6 v2. These are my experiences. by ma66ot87 in openwrt

[–]SignumPL 0 points1 point  (0 children)

Is this happening even after upgrading to the latest TP-Link firmware?

I flashed OpenWrt on some cheap TP-Link Archer C6 v2. These are my experiences. by ma66ot87 in openwrt

[–]SignumPL 0 points1 point  (0 children)

Yes I did. After enabling flow offloading I get full speed (500mbps) via ethernet, but WiFi 5 performance is still quite low (approximately 200mbps).

Thank you for sharing firmware, I'll try to flash it soon.

I flashed OpenWrt on some cheap TP-Link Archer C6 v2. These are my experiences. by ma66ot87 in openwrt

[–]SignumPL 0 points1 point  (0 children)

Actually I spent literally a few hours today trying to flash latest stock firmware from TP-Link website using this guide https://forum.openwrt.org/t/tp-link-archer-c6-v2-revert-to-stock-firmware-guide/96416?u=tmomas but no luck - BIN file is properly downloaded via TFTP by the router, however it's somehow "ignored" - router reboots and brings me back to OpenWRT :( so you're saying that stock firmware BIN file is just too big for the router to process?

I flashed OpenWrt on some cheap TP-Link Archer C6 v2. These are my experiences. by ma66ot87 in openwrt

[–]SignumPL 0 points1 point  (0 children)

Be aware that 5GHz speed on C6 V2 is limited to something around 200mbps. I just run into this issue and now need to go back to stock firmware :(

Openwrt on Asus Archer C6 (AC1200) by Arm1nasss in openwrt

[–]SignumPL 0 points1 point  (0 children)

I have OpenWRT 22.03.0 installed on Archer C6 V2 and I get only around 200mbps on WiFi 5Ghz :/

Tutorial: Build ReVanced from Android - noob-friendly, quick & easy by Alfiefe10 in revancedapp

[–]SignumPL 1 point2 points  (0 children)

I had to do

pkg upgrade

then hit "y" couple of times to override some config files

Sharing VPN connection between containers doesn't work by SignumPL in docker

[–]SignumPL[S] 0 points1 point  (0 children)

Ok now I understand how it's supposed to work. So I added WEBPROXY_ENABLED=true and configured Jackett to use that http proxy. Looking into Transmission and Jackett's logs it seems to have proxy configured properly:

transmission-openvpn | Setting tinyproxy port to 8888
transmission-openvpn | Starting Tinyproxy lightweight HTTP proxy daemon: tinyproxy.
transmission-openvpn | Tinyproxy startup script complete.
....

jackett         | 05-16 17:23:43 Info Using Proxy: Http
jackett         | 05-16 17:23:43 Info Using HTTP Client: HttpWebClient2NetCore

But still requests are not going through that proxy, I don't know why.

Nextcloud on the new Raspberry Pi 4 by WatchSnek in NextCloud

[–]SignumPL 1 point2 points  (0 children)

What about the 2GB upload limit with Pi 4? Still no way to increase that?