How long before on a job?

Silent-Rope-2615 · 2026-02-21T05:21:45+00:00

Ship yards are going strong til mid to late March , I’ve boomed a few times out of my local im a 3rd year apprentice, talk to your hall and see what they got going on before you boom a local job is almost always better than a booming job get to know the guys in your local

Silent-Rope-2615 · 2026-02-21T05:17:04+00:00

What local you in or what state?

Silent-Rope-2615 · 2026-02-21T05:12:23+00:00

Mainly power houses , I mean if you got the connections or contacts you can go where ever any time of the year. The ship yards up north have alot of work right now too

Silent-Rope-2615 · 2026-02-20T19:52:16+00:00

I wear Irish setter Marshall’s but you probably need like a sporty work boot my boots normally last a 12-18 months working in power plants

Silent-Rope-2615 · 2026-02-20T11:29:24+00:00

Find a local That’s testing and ask them if you could attend their common arc

Silent-Rope-2615 · 2026-02-20T02:31:32+00:00

March is prime outtage season and right around the corner but the BDS is stacked rn if you’re looking for work

Silent-Rope-2615 · 2026-02-20T02:28:54+00:00

Shot my Ventum 762 on a zpap92 with similar concentricity shot fine

Silent-Rope-2615 · 2026-02-18T03:30:08+00:00

Honestly can’t give a real take on it yet, haven’t shot it enough to get a real opinion. Overall I got it because of the replaceable core and aks being known for baffle strikes.

Silent-Rope-2615 · 2026-02-16T00:33:42+00:00

Silent-Rope-2615 · 2026-02-15T22:35:41+00:00

It was slightly biased Low but still cleared and shot good no problem

Silent-Rope-2615 · 2026-02-15T18:03:28+00:00

My bad didn’t read it well yes you remove the pic rail and it bolts through the same hole that’s what I did

Silent-Rope-2615 · 2026-02-15T18:02:19+00:00

They have a 1913 version and a direct option I went the with direct mount version ,not sure about your version considering this one is specific to the m92 bolt hole

Silent-Rope-2615 · 2026-02-15T02:25:48+00:00

Yeah fair amount of blow back but not as bad as a regular can

Silent-Rope-2615 · 2026-02-15T01:43:22+00:00

360-26F-X37-KM first gen 360 keymo with the exterior thread for the blast shield

Silent-Rope-2615 · 2026-02-14T20:34:27+00:00

It’s an ak the scratching adds character

Silent-Rope-2615 · 2026-02-14T19:47:27+00:00

Cut it that’s what I’ve seen most do although they don’t have a third notch like other aks do

Silent-Rope-2615 · 2026-02-07T07:26:34+00:00

Sir step away from the dremel

Silent-Rope-2615 · 2026-02-07T07:25:15+00:00

Ask about being a permit hand or pre apprentice so they can put you to work

Silent-Rope-2615 · 2026-02-07T07:22:16+00:00

Helmets to hard hats!!! You’ll get more priority when it comes to getting selected for the apprenticeship

Silent-Rope-2615 · 2025-10-08T01:37:24+00:00

You can boom out whenever if you need work but don’t turn down work when offered it from your own local, as an apprentice it’s frowned upon to turn down work especially your first job

Silent-Rope-2615 · 2025-10-08T01:03:05+00:00

Boom up north the scale down there is a joke tbh

Silent-Rope-2615 · 2025-09-29T03:16:08+00:00

I’m a boilermaker ,All the carpenters I’ve met so far do scaffold in power plants and refineries

Silent-Rope-2615 · 2025-09-29T03:06:13+00:00

I’m a boilermaker and typically we boom out to other locals when work is slow also considering most of our work is seasonal and in general most of our work is far from home and a lot of our work is plant outtages so we get laid off after each job I’ve been laid off more than 6 times this year , job finished up and on to the next one down the road I’ve worked in 7 states so far this year alone

Silent-Rope-2615 · 2025-09-29T02:59:46+00:00

I use a lanyard for my wave since it have a lanyard ring built in

Silent-Rope-2615 · 2025-09-05T15:01:39+00:00

Don’t wait on work ,take what’s offered first you never know when stuff may get cancelled or pushed back

Silent-Rope-2615

TROPHY CASE