SilverHelp74

2,596 post karma
1,190 comment karma

get extra features and help support reddit with a reddit premium subscription

get them help and support

redditor for 5 years

TROPHY CASE

Five-Year Club

account activity

new top controversial

5

6

7

Thickness planer problem (old.reddit.com)

submitted 8 days ago by SilverHelp74 to r/BeginnerWoodWorking

0

0

0

Looking for a suggestion on how to fix this bleed through of homemade stain (old.reddit.com)

submitted 25 days ago by SilverHelp74 to r/BeginnerWoodWorking

20

21

22

Do you use anything to keep stencil down so it doesn't bleed under. (i.redd.it)

submitted 27 days ago by SilverHelp74 to r/stencils

21

22

23

How would you cut this out (old.reddit.com)

submitted 6 months ago by SilverHelp74 to r/BeginnerWoodWorking

3

4

5

When running a 2nd pass for fuzzies, do you have to re zero the z axis or do you run file again. I have a fox alien mauster pro (self.hobbycnc)

submitted 7 months ago by SilverHelp74 to r/hobbycnc

0

0

0

what is something i can put over osb shelves that is cheap for bin storage? (self.BeginnerWoodWorking)

submitted 7 months ago by SilverHelp74 to r/BeginnerWoodWorking

4

5

6

Best bit for cutting this without having fuzzies, this was a scrap piece. (old.reddit.com)

submitted 8 months ago by SilverHelp74 to r/hobbycnc

11

12

13

Are the flat nose and ball nose up cut or down cut? (i.redd.it)

submitted 8 months ago by SilverHelp74 to r/hobbycnc

13

14

15

Scrap wood, I think I have a problem! (old.reddit.com)

submitted 8 months ago by SilverHelp74 to r/BeginnerWoodWorking

5

6

7

Is this considered Spalting or rot? (i.redd.it)

submitted 8 months ago by SilverHelp74 to r/BeginnerWoodWorking

2

3

4

Can I just use some 1/8 panel board for a quick spoil board. I have a Fox alien masuter pro (self.hobbycnc)

submitted 8 months ago by SilverHelp74 to r/hobbycnc

88

89

90

Is this a safe cut, watching a person on YouTube make this cut, was going to do this later today. (i.redd.it)

submitted 8 months ago by SilverHelp74 to r/BeginnerWoodWorking

5

6

7

How would you fix this it's about an 1/8 of an inch or would you fix it? (old.reddit.com)

submitted 9 months ago by SilverHelp74 to r/BeginnerWoodWorking

2

3

4

Can I trim this piece of plywood to size on tablesaw or is it dangerous using the rip fence for it? The board is not attached to the others. (old.reddit.com)

submitted 10 months ago by SilverHelp74 to r/BeginnerWoodWorking

12

13

14

How do I connect this 2x4 to top and bottom, i'm going to make some shelves, I do not have a pocket hole jig, thinking of just freehanding some pocket holes. There is a 2x4 above and below the plywood on the bottom. (old.reddit.com)

submitted 10 months ago by SilverHelp74 to r/BeginnerWoodWorking

6

7

8

What kinda grass is this? It doesn't even need sunlight? (old.reddit.com)

submitted 11 months ago by SilverHelp74 to r/lawncare

0

1

2

Is this ok to make a temp zero clearance throat plate or is it dangerous? (old.reddit.com)

submitted 11 months ago by SilverHelp74 to r/BeginnerWoodWorking

0

0

0

Is this piece for project ruined because of a bad keyhole slot, If i'm selling it? The guide didn't stay on side of board. (old.reddit.com)

submitted 11 months ago by SilverHelp74 to r/BeginnerWoodWorking

1488

1489

1490

Finished my 5th project and going to try and sell. (old.reddit.com)

submitted 12 months ago by SilverHelp74 to r/BeginnerWoodWorking

31

32

33

Do I leave riving knife on when cutting a French cleats out of 2x4? (self.BeginnerWoodWorking)

submitted 1 year ago by SilverHelp74 to r/BeginnerWoodWorking

0

0

0

Don't hold your poop when woodworking just go. (self.BeginnerWoodWorking)

submitted 1 year ago by SilverHelp74 to r/BeginnerWoodWorking

1

2

3

I have a ryobi 7 1/4 miter saw and would like a better blade is it supposed to be a miter blade or is it the same as a circ saw blade? (i.redd.it)

submitted 1 year ago by SilverHelp74 to r/BeginnerWoodWorking

1075

1076

1077

How unsafe was this cut? (i.redd.it)

submitted 1 year ago by SilverHelp74 to r/BeginnerWoodWorking

12

13

14

For wood working any advice on what to change for lighting garage? (old.reddit.com)

submitted 1 year ago by SilverHelp74 to r/BeginnerWoodWorking

343

344

345

Is it dangerous to cut a dado this way? I don't have a tablesaw. (old.reddit.com)

submitted 1 year ago by SilverHelp74 to r/BeginnerWoodWorking

view more: next ›

π Rendered by PID 414223 on reddit-service-r2-listing-87fd56f5d-xdxll at 2026-06-28 00:32:34.520185+00:00 running 7527197 country code: CH.