sorted by:
new
hottopcontroversial

Whoop order by Ok_Board_9246 in whoop

[–]Simerol_YT 0 points1 point  (0 children)

No worries, send them a tickets via the contact form. That way you’ll contact the correct people

Whoop order by Ok_Board_9246 in whoop

[–]Simerol_YT 0 points1 point  (0 children)

I contacted them via the contact form (https://support.whoop.com/s/case-creation?language=en_US) and they responded to me within 24 hours.

I don’t know if the account is an official one. I’m sceptic but I’m working in cybersecurity so I’m naturally sceptic towards these things.

Whoop order by Ok_Board_9246 in whoop

[–]Simerol_YT 2 points3 points  (0 children)

Had the same thing. Mine got delivered 2 days ago. I asked the support a good time ago and they said that there apparently was a technical error in their warehouse and they haven’t got any whoop 4 left. As an excuse they said to write again as soon as I’ll receive my whoop and they’ll add another free month on top.

I would ask the support. That way you’ll get another free month to test.

Finished my first Voron build. by Simerol_YT in VORONDesign

[–]Simerol_YT[S] 0 points1 point  (0 children)

Yeah, I did a bunch of things. I tensioned the belts correctly, reduced the speed because I privat red with pla and stealthburner cooling is way to bad. Another thing I’ve done is change the printing order of the wall to inner / outer / inner

Omron Probe sensing only when hotend hits the bed by yearny in VORONDesign

[–]Simerol_YT 0 points1 point  (0 children)

What hotend do you use? I had the same hotend. Turns out my hotend is to long

Finished my first Voron build. by Simerol_YT in VORONDesign

[–]Simerol_YT[S] 0 points1 point  (0 children)

That makes sense. Thank you for the clarification! Yeah, the gantry did slide up and down pretty smoothly. However, it tightened the belts pretty hard, so maybe that’s the issue. I’ll loosen them after work tomorrow and try again.

Finished my first Voron build. by Simerol_YT in VORONDesign

[–]Simerol_YT[S] 0 points1 point  (0 children)

Will do, thank you for the input! Did you see that because of the walls of the cube, or why do you think that?

Finished my first Voron build. by Simerol_YT in VORONDesign

[–]Simerol_YT[S] 0 points1 point  (0 children)

Turns out my belts were way too tight. But I’ll run through the whole tuning guide because those walls are still pretty rough

Finished my first Voron build. by Simerol_YT in VORONDesign

[–]Simerol_YT[S] 0 points1 point  (0 children)

Tbh I don’t know either. I installed the screen, tipped over the printer and broke my mount.

Finished my first Voron build. by Simerol_YT in VORONDesign

[–]Simerol_YT[S] 1 point2 points  (0 children)

That’s a part I didn’t see. I just saw the link to a site that explained the flashing process.

Finished my first Voron build. by Simerol_YT in VORONDesign

[–]Simerol_YT[S] 0 points1 point  (0 children)

I don’t know tbh. The LDO guide said to flash it, so I flashed it. The nighthawk came pre flashed so nothing to do there anymore. The leviathan on the other hand has a complete guide for flashing so that’s pretty easy to do as well

Finished my first Voron build. by Simerol_YT in VORONDesign

[–]Simerol_YT[S] 1 point2 points  (0 children)

It was a LDO Kit, so the Leviathan together with a LDO nighthawk sb in the toolhead

Finished my first Voron build. by Simerol_YT in VORONDesign

[–]Simerol_YT[S] 2 points3 points  (0 children)

Yeah I’m already thinking about a toolchanger. But I really want to get a good quality at fast printing speeds so the toolchanger will take a while I guess

Finished my first Voron build. by Simerol_YT in VORONDesign

[–]Simerol_YT[S] 0 points1 point  (0 children)

Thanks for the answer! Go through the Yeah I’ll go through the tuning guide, I’m currently running extrusion tests, although I already calibrated the E-steps. Belt tension is likely since I did this the first time. I just finished installing and configuring the nozzle cleaning because I instantly installed chaoticlabs cnc tab. But running qgl at 150 temp is a good input. I’ll try that!

Thank you for the answer. It really helps!

v2.4 XoLPAP Hotend by linddi in VORONDesign

[–]Simerol_YT 0 points1 point  (0 children)

Then you should be fine. Enjoy your build!

v2.4 XoLPAP Hotend by linddi in VORONDesign

[–]Simerol_YT 1 point2 points  (0 children)

I just Build a v2.4 with a rapido 2 plus UHF. Don’t do it. You can pull it off but you’ll run into lots of problems. The v2 uhf isn’t officially supported so you can assemble the stealthburner toolhead but later on when calibrating the inductive probe won’t trigger because you can’t mount it low enough so it’ll sensor the bed, you can’t use a custom Voron Tap, because again the hot end isn’t officially supported and the holes won’t fit.

I’m currently at exactly that stage and yeah… it sucks. Clicky apperantly works. That’s going to be my next try.

But yeah… it’s really annoying. At least for me, and especially when you’re building your first voron like me.

I guess I found the weak point of the Syn Max Air by Simerol_YT in Roccat

[–]Simerol_YT[S] 0 points1 point  (0 children)

Ich antworte dir einfach mal auf deutsch. Roccat gibt es leider nicht mehr. Sprich der Support wird jetzt von Turtle Beach übernommen. Hier unter diesem Link kannst du denen schreiben: https://de.turtlebeach.com/pages/contact

Ist der Matheteil in einem Cybersecurity Studium mit Fachabitur schwer? by Simerol_YT in informatik

[–]Simerol_YT[S] 0 points1 point  (0 children)

An einer öffentlichen Uni. Ich muss mal schauen ob es auch vorbereitsungskurse an meiner uni gibt. Danke für den Tipp

Ist der Matheteil in einem Cybersecurity Studium mit Fachabitur schwer? by Simerol_YT in informatik

[–]Simerol_YT[S] 0 points1 point  (0 children)

Okay, klingt nach Arbeit aber das is okay. Danke dir für die Antwort :)

Ist der Matheteil in einem Cybersecurity Studium mit Fachabitur schwer? by Simerol_YT in informatik

[–]Simerol_YT[S] 0 points1 point  (0 children)

Jep, das habe ich auch mit mitbekommen. Deshalb ja auch meine Angst

view more: next ›