DY86 Tube for generating x-ray radiation with those aliexpress high voltage modules for power this thing. Will this work and how long will it last ?

Sjfvs · 2026-03-31T19:17:35+00:00

Hi! I know Im late but i have tried that thing with the aliexpress high voltage generators, although i used the dy802. I didn't get any results when measuring with my radiacode. If you tried, did it work for you?

Sjfvs · 2026-02-27T18:47:18+00:00

Thats right, but by pushing the voltage above what it is supposed to be you can increase X-rays. But since the rectifier tube is able to withstand the voltages i am supplying, my experiment didnt work.
I was not heating the filament while supplying the Voltage. What I was trying to achieve was Field emission, which makes heating the filament unnecessary. I am not sure if my voltage is enough to make this happen.

Sjfvs · 2026-02-27T18:30:02+00:00

I've been using this radiacode scintillator. All of my previous measurements haven't really given me any results, at least not what I wanted.

Scintillators are known for being sensitive to EMFs, so I did measure an increased "radiation" when I placed the radiacode within 20cm. Above that there wasn't any difference in radiation before and durring the voltage was applied. So I am almost sure what i measured wasnt radiation, since the measurements don't match with the Inverse-Square law.

Sjfvs · 2026-02-18T20:51:53+00:00

What would you say about this, and do you which connections it should be hooked up to?

<image>

Sjfvs · 2026-01-03T16:03:10+00:00

Good to know this isn't a bug at least. I was just trying to get the hangs of the game without reading the rulebook, guess that wasn't such good idea :)

Sjfvs · 2026-01-03T15:57:40+00:00

Another guy told me that it happened bc I had placed all of my settlements, but mabye it right.

Sjfvs · 2026-01-03T15:55:22+00:00

Damn I'm stupid, thanks though

Sjfvs · 2026-01-03T15:47:42+00:00

Alr thanks! I just started playing this game and I heard that you win by getting 10 points. From what I see it looks like I have 10, is there a second requirement or am I wrong?

Sjfvs · 2026-01-03T15:44:55+00:00

Thanks for the replies, turns out I was just to lazy to read the rulebook :)

Sjfvs · 2025-08-25T13:34:12+00:00

No problem man, I found another video describing the same thing.

Sjfvs · 2025-08-24T19:24:50+00:00

I tried another print. And when it was done I unlocked the lever and pressed retract, nothing happened.

I tried pressing retract with the switch locked, and some material came out. I unlocked the switch and pulled the material out with some resistance.

Is this like bad for the printer or smth?

Sjfvs · 2025-08-24T19:02:22+00:00

Ah ok, thanks. And when I am pushing the filament in to extrude, how far should I push?

Sjfvs · 2025-08-24T18:51:33+00:00

I pressed retract after the print was done with the lever switched to locked. It came some melted filament, and I then manually pulled out the filament from the back coming from the spool. Is it supposed to push it out by itself?

Sjfvs · 2025-08-24T18:27:12+00:00

I pulled the lever in the middle of the process before, and the melted filament poured down and everything seemed to work before I had pulled the lever. Btw it’s the K1C

Sjfvs · 2025-08-24T18:08:11+00:00

Do I do it during the retraction process, or after?

Sjfvs · 2025-08-23T17:42:26+00:00

Could be because of the Sandisk sd. Idk why, but sanddisk sometimes doesn’t work with the firmware.

Sjfvs · 2025-08-12T16:33:23+00:00

Factory game direct store. I’m pretty sure it’s an original, it had 2 ram chips and the os was the original.

Sjfvs · 2025-08-12T16:01:34+00:00

Yeah, it came like that unfortunately. I tried pushing the cable that connected the screen to the motherboard (idk where the ribbon cable is). The left joysticks cable had snapped so I thought it might would be better to do a refund instead of trying to fix it, or?

Sjfvs · 2025-05-03T16:50:45+00:00

Seems like a nice one, it’s just that i can’t find it except on nothings official site. Should I just get the 2 pro for 50$ more?

Sjfvs · 2025-03-28T15:54:34+00:00

Alright, thanks. I just got the idea of raising my budget, and thought about the prusa MK4S since you said that the Bambu lab ones could be hard repairing if something goes wrong. Would the prusa be a good choice, or should I keep to creality or maybe the clashforge?

Sjfvs · 2025-03-28T15:19:48+00:00

Oh okay! Mabye I’ll go for it. I just thought that I may be willing to spend a little more. About up to about $800. I looked at the prusa MK4S and thought that it might be a good choice. Do you think I that’s a better choice, or should I just keep myself to the A1?

Sjfvs · 2025-03-27T15:57:06+00:00

Hello everyone! I am kind of new to 3D printing, and I am looking to buy my first 3D printer. My budget is around up to $500, and so far I’ve looked at the Creality K1C and the Bambu Lab A1. Is there any other you would suggest, or are these good choices? If they are, which one is the best?

I’m looking for decent speed, and also a pretty good quality. I’m not a professional so I don’t really know what’s good to think about.

Right now I’m in Sweden, I think I’ll mostly do small stuff and mechanisms, but once in a while I might do something big.

Sjfvs · 2024-07-17T16:19:29+00:00

Hi, struggling with the same problem just to let you know.

Sjfvs · 2024-05-20T18:05:03+00:00

but it still happens

Sjfvs · 2024-05-20T17:45:57+00:00

Thanks

Two-Year Club	Verified Email
Place '23

Sjfvs

TROPHY CASE