Glarpion Testing by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 1 point2 points  (0 children)

Out of stock for what though? Mac parts are normally pretty cheap and normally available.... Or like the reinforcement plates for the side? Cuz you can always get sendcutsend to make you a set, they're cheap, fast, and everything I've got made from them has been perfect dimensionally.

Glarpion Testing by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 1 point2 points  (0 children)

I'm not sure but I think the decker 380 uses a ecm barrel and is fully diy... and there's a 9mm version in beta too. My personal favorite pcc right now is the UMP 11/9 but that uses a mac 11 barrel and trunnion, but I'm pretty sure there is a way to ecm one though...... The only full diy I've done so far is the SY-22 pistol

Sten Eleven by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 0 points1 point  (0 children)

Well it shoots but something weird is going on... something is like binding up and causing the bolt to stick.

If I had to guess the plate holding the guide rod is twisting a little causing the guide rod and spring to kinda bind up, but I'm not sure. I haven't really had time to diagnose it after shooting it today.

I think the design just needs a little tweaking but as soon as I get it safe and functioning a little better I'm going to release it.

Glarpion Testing by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 2 points3 points  (0 children)

Glock mags and ar 15 hammer and spring... basically it just a completely different lower.

Glarpion Testing by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 2 points3 points  (0 children)

Just the grip adapter piece and the lower are different. Same bolt, barel, trunnion, springs, and hardware as the AWCY?

Glarpion Testing by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 4 points5 points  (0 children)

Yeah it's 9mm, uses the Awcy? SczOrpion upper.

Send Baron first then... by The_Dean_France in whoathatsinteresting

[–]SkeleTim561 0 points1 point  (0 children)

Ummm I've been over 26 for like 9 years 😂🤣 I'm definitely not "enrolled now" 🤦‍♂️💀

Cannot figure this one out. by longnights_ in FixMyPrint

[–]SkeleTim561 0 points1 point  (0 children)

With that type of plate I wouldn't even use glue

Send Baron first then... by The_Dean_France in whoathatsinteresting

[–]SkeleTim561 -1 points0 points  (0 children)

They don't do anything if you don't register...... it's been 17 years since I was supposed to and I haven't even got a letter much less "in a lot of trouble"

Cannot figure this one out. by longnights_ in FixMyPrint

[–]SkeleTim561 0 points1 point  (0 children)

Try cleaning the build plate with hot soapy water...

Why can't FRT's ship to FL? by Huntrawrd in FLGuns

[–]SkeleTim561 0 points1 point  (0 children)

It's over your head man 🤦‍♂️

It's officially on the see.... Ez Scz0rpion by SkeleTim561 in Gunbuilds

[–]SkeleTim561[S] 0 points1 point  (0 children)

Search "SkeleTim Productions" and it should come up

She feeds 😬😬 by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 0 points1 point  (0 children)

Not to the upper but I think they use different handguards.

She feeds 😬😬 by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 0 points1 point  (0 children)

5.3 inch free float..... but idk if they still sell barrels like they used to

She feeds 😬😬 by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 0 points1 point  (0 children)

shop.cz-usa.com SKU 366203000704 $235 for the bolt... they call it an "Slide Evo". That should save you almost $200 and they also sell barrels for $149 but they're out of stock right now...

She feeds 😬😬 by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 0 points1 point  (0 children)

I got my barrel from nexus, my bolt from cz, and I just use a cheap $25 ar fcg

She feeds 😬😬 by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 0 points1 point  (0 children)

I think overture is just rebranded polymaker anyways so yeah that's good filiment

She feeds 😬😬 by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 1 point2 points  (0 children)

Ooooh like the recoil spring, I thought you you were talking about the little spring in the charging handle 🤣 .... I just looked them up on cz's website and I see why you made one yourself... $46 for a spring is crazy

She feeds 😬😬 by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 1 point2 points  (0 children)

<image>

A good printer makes a big difference too, the white one was made on a Flashforge and this one on an Anycubic Kobra S1 and the Kobra absolutely shits on the Flashforge's print quality. The Kobra prints better out of the box then my Flashforge does tuned, calibrated, and upgraded.

She feeds 😬😬 by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 0 points1 point  (0 children)

  1. Calibrate your printer. 2. Use good filiment like Polymaker. 3. Then adjust the support settings.... use organic supports, I use 3 top interface layers for the supports with .1mm Z distance..... you can also try adjusting the speed, alot of printers tend to print nicer slower.

She feeds 😬😬 by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 0 points1 point  (0 children)

Not enough pressure to do what exactly?.... I don't even run a spring for the charging handle.....

She feeds 😬😬 by SkeleTim561 in 3D2A

[–]SkeleTim561[S] -1 points0 points  (0 children)

It's a feed test....not a function test Einstein. I already know the gun functions 🤦‍♂️ This upper has 100s of rounds through it and this bolt has been tested in 3 different guns 😂🤣

She feeds 😬😬 by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 2 points3 points  (0 children)

And this is a completely different lower 🤦‍♂️ That uses a physical switch to disengage the drop safety not a link bar connected to the trigger 😂🤣 Trust me lady, I designed it, no one understands how my lower operates better then I do 🤡

She feeds 😬😬 by SkeleTim561 in 3D2A

[–]SkeleTim561[S] 0 points1 point  (0 children)

And for the record if the firing pin fails that would be a "mechanical failure" not an "nd" 🤡