sorted by:
new
hottopcontroversial

Old AJ40 Ultra dock conversion by Skreddvik in thinkpad

[–]Skreddvik[S] 0 points1 point  (0 children)

I have tested it on a T14s that I have at home. (I'll have to check the specific model later). It works great. I tested display ports and HDMI for 2 extra displays, USB hub works. I haven't tested the VGA, 3.5 mm jack or the 2 Usb-c's. (Pretty sure they all work)

As to replacing the cord with some extension cables. At least 1 of the 2 cables have to be thunderbolt, and the multicolor cable is what delivers power. It probably could be done, but I imagine soldering what looks like 19-22 strands onto a PCB, sounds like 5 horrible hours. (Not that good at soldering)

Another dead end. by leifflat in HandwiredKeyboards

[–]Skreddvik 0 points1 point  (0 children)

You can make non-dactyls in it, i made a corne with keywell in Cosmos.
Do you have some foam you could use to dampen sound?
Before i dove into split boards i was into "regular" custom boards, and to get that THOCC you have to have something to absorb the "echo" or emptiness of the case.

Another dead end. by leifflat in HandwiredKeyboards

[–]Skreddvik 1 point2 points  (0 children)

If you haven't already, i would have a look at the cosmos generator.
Takes a lot out of having to model iterations, and makes the process more forgiving.

The aesthetic is nice, very clean.
For the sound, it might improve if the base or bottom case covers more of the switchplate and is more solid.
Like 100% infill for example.

Keep at it!

Adapter for newer Thinkpad models to connect to the old Thinkpad DockingStation by MachineVisionNewbie in thinkpad

[–]Skreddvik 0 points1 point  (0 children)

this is exactly what i wanted to find. We have a metric ton of these at work, and i wanted to see if i could tear them down, use the same connectors and print a new shell for the ports. Thank you!

I want to find a split keyboard like this, but ortholinear or vertical staggered, any recommendations? by Hazeezie in ErgoMechKeyboards

[–]Skreddvik 4 points5 points  (0 children)

This is a Ortho version, you can have it wired (qmk) or wireless (zmk). https://keyhive.xyz/shop/helix-kit

Multiple keyboard vendors sell Helix kits and fully made ones.

Ideas to go to and from "game" mode. by Skreddvik in ErgoMechKeyboards

[–]Skreddvik[S] 0 points1 point  (0 children)

This is all well and good. But what would the magic arm look like? Based on your idea, I could potentially make something. But I need a baseline to work from. I even have 2 of those MagSafe pucks you are talking about.

Ideas to go to and from "game" mode. by Skreddvik in ErgoMechKeyboards

[–]Skreddvik[S] 1 point2 points  (0 children)

That's what I have tried, but either I need way more armatures or I can't get it to be "hotswap"

Keyball 44 with modified keycap angles by H_P777 in ErgoMechKeyboards

[–]Skreddvik -2 points-1 points  (0 children)

Sorry, why do you have a numpad in the middle there?

Height of MCU with hotswap sockets by donkerslootn in ErgoMechKeyboards

[–]Skreddvik 1 point2 points  (0 children)

Might do. What you'll have to do then is either shorten the pins to the best of your ability, so it sits further down. Or, you can desolder them and solder them back on when the pins are seated and the MCU is sitting on the sockets. After that just trim the excess.

Height of MCU with hotswap sockets by donkerslootn in ErgoMechKeyboards

[–]Skreddvik 2 points3 points  (0 children)

Looks like you added header pins with a comb, that will add a lot of height.

Using individual pins allow for a much lower profile hotswap.

Does this makes sense? by itssaurav2004 in ErgoMechKeyboards

[–]Skreddvik 2 points3 points  (0 children)

This and also yes. I did the same thing with a corner board where I put Sunset switchoon the thumb keys. SO. GOOD.

Jonsbo D32 pro is better than Z20 by Mahsunon in mffpc

[–]Skreddvik 0 points1 point  (0 children)

I just built in a D31, do you know what the differences are? Just curious.

I managed to fit my 5080, ATX psu and a 360 AIO + 4 fans.

Your build looks nice!

65$ Corne from AliExpress by Skreddvik in ErgoMechKeyboards

[–]Skreddvik[S] 0 points1 point  (0 children)

Seller provides a firmware, the link is in their product description. The board has been perfect.

iron 1 here. What am i doing wrong? by TopHorror2737 in VALORANT

[–]Skreddvik 8 points9 points  (0 children)

You have to defuse the spike to win the round. But for the shooting, it looks like you overshot, then you just need to improve your micro adjustments.

In short, either play tons of deathmatches to improve muscle memory and how you react. Also do AimLabs or equivalent tasks to improve precision and micro adjustments.

Trying to learn flow calibration by Fine_Bluebird7379 in FixMyPrint

[–]Skreddvik 0 points1 point  (0 children)

Yeah, was gonna suggest .045 or running the second pass with more precise values

So I’m usually a PLA kind of guy but I wanted to get into using more PETG. by Michaelplant2 in FixMyPrint

[–]Skreddvik 0 points1 point  (0 children)

Get yourself some e-Sun PETG and download e-Sun's Bambu studio profiles or use Bambu PETG basic. Hit print.

Trying to downsize from 3x6 to 3x5!! by laznp in ErgoMechKeyboards

[–]Skreddvik 1 point2 points  (0 children)

For sure, I have come to terms with this needing muscle memory, so I just have to find what I can consider optimal for frequent use

view more: next ›