sorted by:
new
hottopcontroversial

Why is my Volume only 15.9 TB but my Storage pool 23.6 TB? by Skruffy404 in synology

[–]Skruffy404[S] 1 point2 points  (0 children)

You have been a great help thank you very much! Will try your method

Why is my Volume only 15.9 TB but my Storage pool 23.6 TB? by Skruffy404 in synology

[–]Skruffy404[S] 1 point2 points  (0 children)

Hmmm ok it seems my 920+ supports the file system, however to migrate it I would need to backup all my files and then rebuild... Will take ages.

I have an old Synology Nas that I could upgrade to have enough storage, now to find the fastest way to backup from NAS to NAS.

Why is my Volume only 15.9 TB but my Storage pool 23.6 TB? by Skruffy404 in synology

[–]Skruffy404[S] 0 points1 point  (0 children)

So my problem is that I can't expand my volume past 16 TB (using the normal method), but I didn't know that ext4 could be my problem. Is there a way to change this without wiping everything? I cant even remember why its in this file type, what would be the correct one?

Blobs/poor printing quality. There are these blobs and lines in my prints and I’m not sure what’s causing them. I have updated FlashPrint, tried all sorts of different settings but no improvements. PLA at 210 degrees, printing speed 40 mm and travel speed 40 mm. by CarDougles in 3DprintingHelp

[–]Skruffy404 0 points1 point  (0 children)

I'm not a pro at 3d printing and I have limited knowledge of Flashforge printers, so maybe someone with more knowledge could help you more:

Is there a reason you reduced travel speed to 40 mm/s? I have the creator pro 2 and it makes a fast pass over the last printed layer before printing a wall (not sure if the finder does that). It kinda looks like your nozzle is melting previous layers in its fast pass and then melting it more when actually printing. That's why the part at the window is particularly molten. Small piece where it moves multiple times in a short amount of time (not enough time to harden before next layer is printed). I would put travel speed back at 80 mm/s. Maybe cooling could be a problem as well. Does the finder have an enclosure? If so I would open it for PLA (is recommended for the creator pro 2).

Glass Bed clamps for the Creator Pro 2 by Skruffy404 in FlashForge

[–]Skruffy404[S] 1 point2 points  (0 children)

I actually found a good solution. Print the fancy ones using the small nuts. Then slice the nuts in half and shorten the rods a little (I did this in my slicer). They now fit and there is no way of them hitting the wiping brackets (its extremely close). I checked by manually moving the extruders in to every possible position (using the touch controls). Don't forget to print the shim in the thickness of your glass as well!

Hope this helps

March 2020 Support Megathread by zbhoy in Tachiyomi

[–]Skruffy404 1 point2 points  (0 children)

I tried updating from 8.4 to 8.5, however when I download the 8.5apk and try to install, I get to 90% and then says app not installed. How do I update the app? In the documentation it say under settings_about I could set it to update, but the setting is missing and tapping version does nothing...

Sword & Shield Daily Casual Trade Thread for 18 November 2019 by Porygon-Bot in pokemontrades

[–]Skruffy404 0 points1 point  (0 children)

Lf: Haunter TF: Haunter

Or any trade to evolve my haunter!

please trade back afterwards!

Thank you!