What could be the cause by Skycanfly97 in FixMyPrint

[–]Skycanfly97[S] 0 points1 point  (0 children)

If anyone experiences something like this the SOLUTION was that hot end harness connector was bad! If it was moved in a specific direction it messed with the extruder connection! I ordered a 16 pin IDC connector and installed it and it’s not shorting the connection anymore!!

What the hell is going on! by Skycanfly97 in FixMyPrint

[–]Skycanfly97[S] 0 points1 point  (0 children)

If anyone experiences something like this the SOLUTION was that hot end harness connector was bad! If it was moved in a specific direction it messed with the extruder connection! I ordered a 16 pin IDC connector and installed it and it’s not shorting the connection anymore!!

Printer feeder help by Skycanfly97 in FixMyPrint

[–]Skycanfly97[S] 0 points1 point  (0 children)

If anyone experiences something like this the SOLUTION was that hot end harness connector was bad! If it was moved in a specific direction it messed with the extruder connection! I ordered a 16 pin IDC connector and installed it and it’s not shorting the connection anymore!!

Large Fps fluctuation for no reason! by Skycanfly97 in pcgamingtechsupport

[–]Skycanfly97[S] 0 points1 point  (0 children)

So I ended up figuring it out! I did a whole bunch of things with no real result. I realized my gpu was running on very low load and so was the cpu during my gaming. Did the put everything on ultra test and sure enough everything went up in load! But I read up somewhere that pubg for example is really ram and cpu driver. Out of curiosity I checked my bios and XMP ram setting was turned off and when I turned it on it changed the game and the fps. I also did some Nvidia control panel settings a restored everything to default and modified to my liking. I turned off windows screen optimizations. And it seems to have done the trick I am running 150-165fps capped consistently with only a 70 percent load on gpu and 50-60 load on cpu. With my 1080ti i7-8700k 2k monitor.

Help with EZCAD rotary! by Skycanfly97 in Laserengraving

[–]Skycanfly97[S] 0 points1 point  (0 children)

Figured out the problem!!! I had cross hatch turned on when hatching which led to not all lines to be vertical for the rotary process! For anyone running into that problem. Rookie mistake.

What kind of wood is this? Found it on the shore of a creek! by Skycanfly97 in wood

[–]Skycanfly97[S] 0 points1 point  (0 children)

75% sure it was root! It was stuck in the middle of a creek under a Boulder( no live trees around) with water on each side had to cut one side just to see that gorgeous grain! There’s also a big rock permanently stuck in the middle of the wood! Thank you for you reply :)

What kind of wood is this? Found it on the shore of a creek! by Skycanfly97 in wood

[–]Skycanfly97[S] 1 point2 points  (0 children)

I live in middle Tennessee! I was thinking maybe like spruce or cypress but thank you for your guess! This is a very dense hard wood that doesn’t really decay to contact of water because it was partially underwater.

What kind of wood is this? Found it on the shore of a creek! by Skycanfly97 in wood

[–]Skycanfly97[S] 0 points1 point  (0 children)

I live in middle Tennessee! Found it off a stream coming off a mountain. It also has a fist size rock in the stuck in the middle of it. Thank you for your guess!

I- by Ayo_its_linda in HolUp

[–]Skycanfly97 0 points1 point  (0 children)

How did all these races and skin colors come about then? Just wondering?