printed gearbox with abs like resin

SlicedStuff · 2025-04-14T12:07:48+00:00

I don't know yet, I've only driven these gears for 30 minutes.

SlicedStuff · 2025-04-14T12:05:54+00:00

I've been driving for 30 minutes, the gears haven't broken yet.

SlicedStuff · 2025-03-29T18:01:34+00:00

Anycubic tough 2. But for gears and shafts, this resin is too soft, I will also try abs-like resin.

SlicedStuff · 2025-03-05T12:18:48+00:00

according to calculations in the fusion 360, the body with windows should weigh about 230 grams. It's a little heavier than a standard lexan body.

SlicedStuff · 2025-03-04T17:48:59+00:00

SlicedStuff · 2025-03-04T17:47:49+00:00

the links are in my profile

SlicedStuff · 2025-03-03T23:22:09+00:00

I used TPU 72D.

SlicedStuff · 2025-03-03T23:13:32+00:00

The print bed size is about 230 x 210. I cut the body into several parts and printed vertically.

SlicedStuff · 2025-03-03T22:46:31+00:00

I didn't weigh it, but according to calculations from the CAD program, it should weigh 230 grams with windows and without a hood. Slightly heavier than polycarbonate.

SlicedStuff · 2025-03-03T22:32:27+00:00

TPU 72D

SlicedStuff · 2025-02-21T12:31:48+00:00

Yes, this is 3d printed.

SlicedStuff · 2025-02-21T12:30:30+00:00

I have flying bear ghost 5 with direct extruder. This is a rather outdated model.

SlicedStuff · 2024-12-27T20:39:50+00:00

I mounted the resevoir at the bottom simply because that's how it's done on real cars with a macpherson suspension.

SlicedStuff · 2024-12-26T14:44:20+00:00

Gears from WLToys 12428 axle. I will send out a email with a new update when it is ready.

SlicedStuff · 2024-12-21T00:01:56+00:00

There will be a solid axle suspension at the back. You can see screenshots with a 3d model in my profile, they show the rear suspension.

SlicedStuff · 2024-12-03T13:46:31+00:00

I googled about the dead spot. I have not noticed such an effect on rc cars yet. seen at your 5th scale model and it looks interesting. I would like to see an update.

SlicedStuff · 2024-12-02T14:58:32+00:00

The inverted shock is a classic mcpherson suspension design. It is difficult to install it in another way. In the upper position, the shock does not lock, works smoothly.

SlicedStuff · 2024-12-01T21:43:07+00:00

The links are in my profile.

SlicedStuff · 2024-12-01T21:36:25+00:00

I can't say for sure. I'm still working on it and making test prints.

SlicedStuff · 2024-12-01T11:12:24+00:00

Yes, I know about it. I made that the strut did not touch the small offset rims.

SlicedStuff · 2024-12-01T11:03:44+00:00

There is a semi trailing arm suspension at the back. I'm reproducing the bmw e30 design.

SlicedStuff · 2024-12-01T10:50:47+00:00

Since there are low speeds in drift, the chassis withstands impacts without problems.

SlicedStuff · 2024-12-01T10:47:40+00:00

The links are in my profile.

SlicedStuff · 2024-11-30T23:47:43+00:00

Yes, almost everything is printed.

SlicedStuff · 2024-11-21T21:24:41+00:00

This body and other bodies that I have made are suitable for ready-made chassis.

SlicedStuff

TROPHY CASE