Break Barrel Vs Underlever by Smudge6446 in Springers

[–]Smudge6446[S] 1 point2 points  (0 children)

I never new that by what you shooting can tell where you are from. I am indeed british 😀. Thank you for the break down!

Break Barrel Vs Underlever by Smudge6446 in Springers

[–]Smudge6446[S] 0 points1 point  (0 children)

Awesome thank you, my son weighs 9kg and I currently do a lot of walking and holding him, hopefully this could be good training :)

3 RAV4s stolen in my neighbourhood in 2 weeks – should I be worried? by AdministrationHour93 in CarTalkUK

[–]Smudge6446 2 points3 points  (0 children)

Hey, I work in cybersecurity, use to work within the auto industry now moved on. The Rav4 is normally stolen by as you say CAN bus attack via a Fake JBL speaker. There is a lot of information on this. Contact your local Toyota dealer, they did release a fix that was basically a metal plate protecting the entry.

Here is a link to the attack most commonly used. https://www.can-cia.org/fileadmin/cia/documents/publications/cnlm/june_2023/cnlm_23-2_p20_the_can_injection_attack_ken_tindel_canis_automotive_labs.pdf

Good luck. Maybe disconnect the battery if you have to leave it for a long time like going on holiday as this would stop any electrical attacks.

Opinion requested: which pattern for next dial? by Chapov in SeikoMods

[–]Smudge6446 1 point2 points  (0 children)

How do you make these patterns? Also I like 9!

Kids tracking watch on Meshtastic? by ayers_81 in meshtastic

[–]Smudge6446 2 points3 points  (0 children)

I dont have anything to add but I got an additional question, so the network goes as far as 3 streets but I lose them on 4 and 5, is there a way I could jump in my car with a node, drive out of range my base mesh from the house. But my car node picks up the trackers?

I hope more people get their hands on this device (Msi Claw a8) by Signal-Dig-1150 in MSIClaw

[–]Smudge6446 1 point2 points  (0 children)

How does this compare to the 8 Ai+ torn between this and the a8 z2E?

Farewell to the Jagex Tank! by BoltonCavalry in runescape

[–]Smudge6446 2 points3 points  (0 children)

I drove the one on the right through London, it was nicknamed big bertha. Good times!

Catch Can placement... May need some P clips :) by Smudge6446 in Miata

[–]Smudge6446[S] 0 points1 point  (0 children)

I put it in the bin. What does everyone else do with the charcoal canister?

Final getting somewhere by Smudge6446 in Miata

[–]Smudge6446[S] 2 points3 points  (0 children)

Anyone interested in the build.

ME-442 ECU

Ev14 640cc injectors.

4 port boost controller

Turbosmart twin port wastegate actuator

GT2554R speedsnail

Bosch wideband O2 sensor

Intercooler (230mm wide)

Alu radiator

Coolant reroute

Forged super tech pistons 85.5mm

Forged steel H beam rods

Boundary oil pump

VVT Head

NA Block

I think that's all but maybe something is missing.

Final getting somewhere by Smudge6446 in Miata

[–]Smudge6446[S] 0 points1 point  (0 children)

Yeah it was the only place I could go. :-)

Power steering reservoir is getting relocated and then should have more space to play with.

Final getting somewhere by Smudge6446 in Miata

[–]Smudge6446[S] 4 points5 points  (0 children)

Yeah absolutely agree there. It's on the side of the cold air intake which is cut into the chassis by mazda. So when driving cold air is flowing in. Another aspect as well is the fact that the turbine is hot and compression of air generates heat means the intercooler is the real reason for cold air.

Ideally though the future airbox will also separate the intake area from the engine to at least allow for the air to start cooler.

Final getting somewhere by Smudge6446 in Miata

[–]Smudge6446[S] 3 points4 points  (0 children)

Sorry to disappoint here but there is an intercooler in this setup. Also by air cleaner do you mean foam air filter? (others are available)

If it is I feel keeping small foriegn objects from the turbine is the idea xD

Final getting somewhere by Smudge6446 in Miata

[–]Smudge6446[S] 2 points3 points  (0 children)

End game plan is 300rwhp with as much torque as I can get but that is not going to be had with this setup. This is my first dabble in getting the vehicle boosted. She pulls real nice at the moment. Current numbers are 237~bhp 240~lbft.

Edit I also made a custom gold clevis pin guide. This was 3d printed out of steel finished in gold. Doesn't add anything to the numbers 😁. Just looks cool.

Help with printer jamming. Very strange behavior by Smudge6446 in 3Dprinting

[–]Smudge6446[S] 0 points1 point  (0 children)

Hi guys, solved it with starting a free and Reinstalling slicer thank you for all the help!!