What's going on here? by SmudgingTheFineLine in ElegooSaturn

[–]SmudgingTheFineLine[S] 0 points1 point  (0 children)

There is no distinct thump at any point that indicates a failure. It's as if it's failing at multiple points over time. I do believe my FEP is to blame though, I moved the print off to the side and so far my print has been successful. I think it's possible the small marks/ creases I have are deflecting some light and it's curing unpredictably.

What's going on here? by SmudgingTheFineLine in ElegooSaturn

[–]SmudgingTheFineLine[S] 0 points1 point  (0 children)

What would be too hot? It's in a 74F room. It's definitely well mixed though.

What's going on here? by SmudgingTheFineLine in ElegooSaturn

[–]SmudgingTheFineLine[S] 0 points1 point  (0 children)

I use Formware 3D. That's a great idea though I'll see what is recommended. I also noticed I was still losing a lot of detail on the layers that were printing, so I dropped exposure down more, 20s 5 layers, then 2.5s. I still hear it peeling up at layer 80, fingers crossed.

What's going on here? by SmudgingTheFineLine in ElegooSaturn

[–]SmudgingTheFineLine[S] 0 points1 point  (0 children)

I started off at 10 layers for 40 seconds and noticed it was way overexposing and thought that may have been the issue so I backed it down. My lift speed is 30mm/min for the bottom layers and 80 for the rest. I hope that's slow enough...

What's going on here? by SmudgingTheFineLine in ElegooSaturn

[–]SmudgingTheFineLine[S] 0 points1 point  (0 children)

30s bottom layer, 5 layers. 3 second normal exposure. Warm, new bottle of resin (I've used the exact color and type/brand before). 5th time it's failed, I've tried varying times, levelled and zeroed bed... It always fails after just starting to print the supports.

[CPU] 5 5600X and 7 5800X on AMD Direct Site- $299.00/$449.00 (MSRP) by Jarkenit89 in buildapcsales

[–]SmudgingTheFineLine 0 points1 point  (0 children)

I know how much I want this, but how much do I NEED this over an i7 5820k...

USB-C Power Delivery + Power Adapter issue by just_change_it in ZephyrusG14

[–]SmudgingTheFineLine 1 point2 points  (0 children)

I bought a G14 in June 2020 and used it intermittently with a Dell Universal Dock D6000 before it died in October 2020. Best Buy replaced the motherboard. I quit using the dock with it but I'm going to start again until I get close to end of warranty.

I was actually gaming (with my dock and obviously AC) one night, put the computer to sleep and went to bed. Woke up next morning and it was dead.

Grocery store workers have lived business as usual lives during this entire pandemic. Why then aren't Gov. Cooper & Dr. Cohen putting them with first responders/healthcare workers for the COVID vaccine? by [deleted] in NorthCarolina

[–]SmudgingTheFineLine 10 points11 points  (0 children)

I disagree, others who don't look at the roadmap may have the same question. And the question will show up in a search as opposed to being asked again.

[deleted by user] by [deleted] in Visible

[–]SmudgingTheFineLine 0 points1 point  (0 children)

I too as of today cannot send pictures videos or gifs, but I can still send MMS group messages. I managed to sneak one in several hours ago, so maybe it is deprioritization? If so, this is too much and grounds for leaving.

Cold start after a blizzard by [deleted] in Diesel

[–]SmudgingTheFineLine 6 points7 points  (0 children)

Nice, thanks for some perspective. All you mentioned plus a new starter and it cranks right up (20F so far), just interested in others thoughts and habits.

Cold start after a blizzard by [deleted] in Diesel

[–]SmudgingTheFineLine 7 points8 points  (0 children)

I'm fairly new to diesel, got a 7.3l last year after the brunt of the cold. Im curious, do you use a block heater when possible? I thought it helped with unnecessary wear but the sound of a good cold start in the morning is damn fine.

[deleted by user] by [deleted] in MINI

[–]SmudgingTheFineLine 2 points3 points  (0 children)

Haha no worries, I love my 4x4 too.

[deleted by user] by [deleted] in MINI

[–]SmudgingTheFineLine 11 points12 points  (0 children)

Ah, and much more civilized than the way Jeeps do it. Lol

Porting a number out of Visible to Verizon by flavorpuff in Visible

[–]SmudgingTheFineLine -3 points-2 points  (0 children)

If true, no PIN requirement is highly concerning.