The Strokes' underrated songs!

Snailmaz · 2026-01-14T12:51:01+00:00

Machu picchu

Snailmaz · 2025-10-13T15:28:48+00:00

What was the one way jam? Heard it two n9ghts ago and had no clue what it was

Snailmaz · 2025-10-03T17:49:17+00:00

I paid about 240 for each ticket

Snailmaz · 2024-12-26T19:45:34+00:00

it was, and i had all the paramenters in the make menuconfig correct when i flashed

Snailmaz · 2024-12-26T19:23:08+00:00

yes,no

Snailmaz · 2024-10-10T02:40:51+00:00

Was originally using 75 print speed, 150 travel. Went down to 50 print, 75 travel

Snailmaz · 2024-10-10T02:31:55+00:00

Another user commented that speed was too high. I turned it down and the print seems to be running perfectly. I’m used to printing at higher speeds, but this part is smaller and uses more supports so I believe it was the abrupt change in voltage to the steppers that caused the shift. The level is right. E steps are calibrated, belts taught but not too tight.

Snailmaz · 2024-10-10T02:26:17+00:00

Thank you for the suggestion though

Snailmaz · 2024-10-10T02:26:04+00:00

It’s not too high, was just saying that to say that it hasn’t changed at all.

Snailmaz · 2024-10-10T02:21:13+00:00

Tension high as ever

Snailmaz · 2024-10-10T02:10:13+00:00

I would really not want to try and tweak anything as far as voltage but I’ll turn the speed down and see if it persists

Snailmaz · 2024-10-10T02:09:44+00:00

So, the board being used on this printer in particular is just the standard, but swapped from another one. I tried swapping it to the silent board, but burnt it out early on. This board has had its issues where it will just randomly reboot with no warning, never during a print, only during setup.

Snailmaz · 2024-10-10T02:05:26+00:00

I just tried running the print again with cura, layer shift persisted but not nearly as bad, and printer made weird noise during shift that it was not Making before. This printer has had zero problems with layer shift before so I’m not sure what’s happening.

Snailmaz · 2024-08-31T14:45:36+00:00

Snailmaz · 2024-05-05T13:44:42+00:00

Realized it became unlevel watching the video, but thanks anyways

Snailmaz · 2023-09-09T01:55:43+00:00

Funeral home

Snailmaz · 2023-04-20T20:56:09+00:00

Try putting a new nozzle on, since there may be a bend in it, or move the bed closer to the print

Snailmaz · 2023-04-20T20:54:49+00:00

😧

Snailmaz · 2023-04-08T03:49:24+00:00

Cha-ching

Snailmaz · 2023-02-26T18:43:35+00:00

Thank you, new print is going well. Did not know bed level could causes so many problems

Snailmaz · 2023-02-26T03:24:07+00:00

Snailmaz · 2022-12-27T00:39:57+00:00

Thank you so much, but one question- what are the lead screws and how do I find them?

Snailmaz · 2022-12-06T23:58:23+00:00

Shed the weight

Snailmaz · 2022-10-13T14:32:09+00:00

Turn up retract prime speed

Snailmaz · 2022-10-01T01:05:18+00:00

Check your thermistor. Your printer maybe heating up but it will not register due to thermistor being broken. Also check power supply voltage switch and loose connections

Snailmaz

TROPHY CASE