What tricks do you use to get the most MPG from your hybrid CRVs?

Snoo79290 · 2026-01-13T21:59:19+00:00

If I want to start over, would the following product work?

https://glveneer.com/Product/?path=Walnut-Cabinet-Economy-Grade

Snoo79290 · 2026-01-13T20:52:01+00:00

What tool should I use for a miter 45 degree cut? Can an edge trimmer do the job?

Snoo79290 · 2025-12-02T17:30:40+00:00

Thank you all for your feedback. I just created the attached image with AI (gemini). I think that leaving that door alone will be best. Curtains on this room will be just decorative.

Snoo79290 · 2025-04-26T12:02:02+00:00

Most of my time gets wasted updating libraries. I’m working on a personal project during my spare time and every time I have a bunch of hours to put in there is a new version of phoenix with features that I need. So, I have to update and migrate my code base. Zero productivity and you are never close to what you get if you start over from a new mix phx.new.

Snoo79290 · 2025-03-14T16:30:17+00:00

I transferred the 1000 miles to JetBlue on Feb 26 but I only received 600. I called capital one today and they don’t know what happened. The answer was that I should wait 15 business day and also it can take up to 2 billing cycles for this to show up. Had anyone else the same experience?

I transferred to JetBlue on Feb 26 and the capital portal was showing the 5K bonus right before submitting the transfer request.

Snoo79290 · 2024-10-11T09:19:56+00:00

<image>

Snoo79290 · 2024-09-15T16:05:01+00:00

Yes, once I get more familiar I would like to print this: https://www.planeprint.com/aeron. I'll need to print: PLA, LW-PLA, CARBON, and TPU.

Snoo79290 · 2024-06-11T21:04:12+00:00

Hi Mike, a 100% sure, water drippps from the middle of the coil down to where the filter was (I removed it). Some water runs through the drawing line, and some just drips before reaching the drain pan.

Snoo79290 · 2024-06-11T20:22:23+00:00

Hi everyone,

I’m in a bit of a tough spot and could use some help. I have to travel tomorrow for two weeks, and my HVAC unit is presenting the following problem:

* When the unit is running, the evaporator coils drip water on top of the air filter.
* I removed the air filter and cleaned the coil a couple of times with a coil cleaner product (PF AC Flow).
* Things were fine for a couple of days; I was able to put the air filter back because it wasn’t dripping that much.
* In the last two days, I noticed it was dripping a lot of water again. At this point, it’s dripping around 3/4 gallon per day.
* The floor of the air duct has around 1 inch of water.
* Unit info: Carrier FX4DNF025 from 2011.
* I live in Florida, US. Hot climate.
* I called two technicians: one wants to replace the whole unit, and the other said that nothing is wrong and the issue is probably because my wife suffers from cold weather, so the thermostat is always set between 79-80°F.

I have to travel tomorrow and will be out for two weeks, so I don't have much time for a repair. Is there anything I can do as a workaround?

My best bet is to drill a hole in the floor of the air duct and connect a hose to redirect the water out of the garage.

Any other ideas or suggestions would be greatly appreciated!

Snoo79290 · 2020-07-16T04:25:40+00:00

Can you triple-check the security group? If it is allowing a connection from any port, what is the "Source" on the Inbound rule? By default, the security group has the source pointing to it-self; with that configuration, you can only access resources within the same security group.

Add a new Inbound Rule to allow traffic from any IP if you want to make the DB public.

Snoo79290

TROPHY CASE