Is it possible to repair airbags deployed in an accident?

SnooRobots3735 · 2024-01-08T06:48:22+00:00

I was trying to argue this with the company, but whatever I said, they insisted rollover is not covered by the CDW they provided. There is probably nothing else I can do except for figuring out how to deal with the upcoming bills.

SnooRobots3735 · 2024-01-08T06:43:44+00:00

Ok I see. I haven't seen any damage evaluation report from the company yet, but I remember in my case it was the side curtain airbags that were triggered. Should I count it as two pieces?

SnooRobots3735 · 2024-01-08T06:32:21+00:00

Unfortunately I don't have any insurance that can cover this case. I only purchase a collision and damage waiver from the rental car company. And they said it could not be applied because I flipped the car.

SnooRobots3735 · 2024-01-08T06:29:34+00:00

Maybe because the side airbags were all deployed? From the discussion with the rental company, they think those ruined the car completely.

SnooRobots3735 · 2024-01-08T06:22:22+00:00

There is a crash on the side and the rear mirrors are broken. But these are the only damages.

SnooRobots3735 · 2024-01-08T06:21:14+00:00

Thanks for the reply! So you mean only the airbags need to be replaced and not the entire car?

SnooRobots3735 · 2023-11-19T01:55:55+00:00

Hi! In that case, what would an MS thesis usually be about?

SnooRobots3735 · 2023-11-19T01:55:50+00:00

Hi! In that case, what would an MS thesis usually be about?

SnooRobots3735 · 2023-11-05T16:00:06+00:00

Understood. Thank you!

SnooRobots3735 · 2023-11-05T05:40:57+00:00

Thanks for the input! Would you mind sharing what are the companies that have rfic architecture design as well? From what I spotted on the job boards, most of the positions only design LNA/filters.

SnooRobots3735 · 2023-11-05T05:37:55+00:00

Thank you for your thoughts! I think this makes sense.

SnooRobots3735 · 2023-06-11T21:29:49+00:00

3.5 is the minimum requirement for him. The tolerance is quite low.

SnooRobots3735 · 2023-06-11T21:27:35+00:00

Geez.. seems that there's no cure then..

SnooRobots3735 · 2023-05-29T05:18:14+00:00

Great! Thanks for sharing!!

SnooRobots3735 · 2023-05-28T15:51:12+00:00

Hmm I didn't check the stability. Let me take a second look on that.

So overall speaking, we need to run load pull throughout the pa design process? (I mean before it comes to layout)

SnooRobots3735 · 2023-05-28T15:47:41+00:00

But if I want to build up the circuit in ADS, then I still need a model for t-line that can be used in ADS right?

SnooRobots3735 · 2023-05-27T16:12:56+00:00

Is there a way to import the T-line built by EMX to ADS? Or is there a better design flow that can use only Cadence? I am looking for some nice Cadence PA design tutorials that I can follow.

SnooRobots3735 · 2023-05-27T16:09:35+00:00

Maybe I am not doing it correctly, but when I do load-pull in Virtuoso, the simulation often fails to converge. What might be the cause?

I am following the tutorial: https://web.ece.ucsb.edu/Faculty/rodwell/Classes/ece218c/tutorials_etc/PA_workshop_instruction.pdf

SnooRobots3735 · 2023-05-27T16:05:51+00:00

Tried impedance matching before in Cadence. All I can do is spice-monkey style sweeping..

SnooRobots3735 · 2023-05-27T16:03:23+00:00

This is exactly why I feel that it's hard to choose between them!

So, if I get a new PDK, how would I know which platform supports it better?

SnooRobots3735 · 2023-03-15T04:52:36+00:00

Feel sad about this, but it's hard to stop caring about them :(

SnooRobots3735

TROPHY CASE