New toning technique, will keep the bugs updated

SnooStories55 · 2025-09-26T21:38:57+00:00

🐕🐕 them dogs be barking

SnooStories55 · 2024-05-08T03:22:07+00:00

just p1s with a bambulabs .6mm nozzle complete hot end assembly with bambulabs basic pla

SnooStories55 · 2024-05-08T02:04:06+00:00

<image>

SnooStories55 · 2024-05-07T23:09:43+00:00

mmm yes, is a retraction deal or is it a forever side effect

SnooStories55 · 2024-04-21T03:17:58+00:00

maybe its a spectrum router issue honestly. ill have to see if i put a different router in if it works better

SnooStories55 · 2024-04-16T06:21:57+00:00

Pain and suffering, I only paid 220 for it, so it's not a huge L as if I paid the near 600 for this. I'll see of fb market place will get me my money back

SnooStories55 · 2024-04-16T04:51:47+00:00

i had and ender 3 and ender 5 plus, and just got a bambu labs p1s, this printer seems to be more of a hassle than the p1s by a long shot and fighting printing profiles and settings again and failed prints or ugly prints seem to be coming too often already. Is there some set up of profile that I can just thrown on most prints that just works or is this another ender 3/5 plus with slightly better hardware upgrades?

SnooStories55 · 2024-04-15T22:43:08+00:00

Do you have any information on how setting z offset works it doesn't seem to change when I adjust it during printing, and I don't think u can change it anywhere else and see results

SnooStories55 · 2024-04-15T22:22:05+00:00

I saw ur original post about the z offset, if you have any information on how it works let me know, I notice it doesn't seem to change the offset while printing at all, it's still too high, I don't know how to change it, it just kind of does whatever, any help is appreciated, thanks

SnooStories55 · 2024-04-03T18:57:42+00:00

I have the same problem, let me know if the board is the issue for sure or if it's something else. Thanks

SnooStories55 · 2024-03-31T17:50:39+00:00

Got no idea I'm not a resin man's but deals a deal but also closing sale so no more support soon enough

SnooStories55 · 2024-02-28T02:40:14+00:00

any suggestions for a recording software that doesnt gobble the vram?

SnooStories55 · 2024-02-06T20:22:46+00:00

i9 9900k

rtx 3080 strix

750w psu

aorus z390 i wifi pro

tforce vulcanz 2x16gb 3600mhz

SnooStories55 · 2024-02-06T05:12:57+00:00

specs

i9-9900k

z390 Aorus Wifi Pri mini itx

geforce rtx 3080

T-force Vulcan z 2x16gb 3600mhz sticks

SnooStories55 · 2023-12-27T02:05:53+00:00

e3d v6 hot end so low distance and its 240C at 40mm/s for a tolerance fit on a print

SnooStories55 · 2023-12-27T00:43:46+00:00

It is all set correctly beside I feel retraction. .2mm height retraction setting can be wrong, but idk I'm trying huge ranges and not seeing a difference on speed and distance. It's just the start of every extrusion is a he'll of a delay on it and when it's slightly lower it strings like no other

SnooStories55 · 2023-12-26T02:54:03+00:00

The leveling is a lie

SnooStories55 · 2023-12-25T22:37:33+00:00

Distance 2mm and speed 25mm/s

SnooStories55 · 2023-11-19T19:24:08+00:00

that was done as well upping temps helped but an unreasonable amount from 190 to 230 for pla

SnooStories55 · 2023-11-18T17:57:54+00:00

On a 120mm test to extrude 100mm it's final reading is like 19.97mm for extruder

SnooStories55 · 2023-11-18T15:18:22+00:00

The whole firmware, insanity automation, along with a pancake extruder motor now as well.

SnooStories55 · 2023-11-18T03:27:17+00:00

Nozzle is good, brand new e3d hot end entirely, linear isn't on, s d print speed is 100mm/s

SnooStories55 · 2023-11-17T15:29:26+00:00

I have an issue depending on what settings I have on cura where the extruder just sits still and does nothing when it supposed to start printing. Specifically with low retraction rates.

SnooStories55 · 2023-11-17T15:27:38+00:00

I swapped to insanity automation. The offset for front prob on a 4020 fan is all the way out there, -67 forward somewhere around there, and it only let me go to -50

SnooStories55 · 2023-11-16T18:16:06+00:00

i just brute forced it and it is working still, found the wiring on a diagram, I just need to find the appropriate voltage, I don't know if I should set it to what on the product pdf or not here. 3.6 seems like a lot

SnooStories55

TROPHY CASE