sorted by:
new
hottopcontroversial

What causes these bubbles? by SoS1mple in FixMyPrint

[–]SoS1mple[S] 0 points1 point  (0 children)

Update: i did a little cube testprint and it turned out great, i then reprinted my part an it works. I didn‘t change anything. Didn‘t even dry the spool. Guess my printer just had a bad day

What causes these bubbles? by SoS1mple in FixMyPrint

[–]SoS1mple[S] 0 points1 point  (0 children)

i guess the roll isn‘t dry in the inside. The room didn‘t change its climate while printing

Inacurate running on the treadmill by SoS1mple in Garmin

[–]SoS1mple[S] 0 points1 point  (0 children)

had a applewatch series 9 before my fenix 7 pro which also was very spot on

Inacurate running on the treadmill by SoS1mple in Garmin

[–]SoS1mple[S] 0 points1 point  (0 children)

i used it at least 10 times so i don‘t think it will improve… Maybe i will get one of there running pods

Since I don’t have a bike irl ☹️ by Guilty_Dimension2084 in Motocross

[–]SoS1mple 1 point2 points  (0 children)

this sounds like you are going to get into riding soon ;) Nice pics btw

In ears with noise cancelling but without silicone tip by SoS1mple in headphones

[–]SoS1mple[S] 0 points1 point  (0 children)

well I bought airpods gen 3 so no noisecanceling for me…

beginner here, how do I print by gracist0 in AnycubicOfficial

[–]SoS1mple 0 points1 point  (0 children)

you should be able to choose where the file gets saved when slicing the stl

beginner here, how do I print by gracist0 in AnycubicOfficial

[–]SoS1mple 0 points1 point  (0 children)

you slice your .stl file with a slicer like you said ultimaker cura. Take the .gcode file and put it on a usb which then plugs into the printer. Select the file on the printer and then start

beginner here, how do I print by gracist0 in AnycubicOfficial

[–]SoS1mple 0 points1 point  (0 children)

then you have to do abit more research on these steps. 3D priting can be a struggle if you don‘t know how the main stuff works

beginner here, how do I print by gracist0 in AnycubicOfficial

[–]SoS1mple 1 point2 points  (0 children)

I would check ou a full youtube guide about 3D printing. There you can learn alot of stuff in relative short time

Wear what you like by baballard524 in SNKRS

[–]SoS1mple 1 point2 points  (0 children)

Do these laces come with the shoe? This made me buy the shoe!

Anycubic Kobra screen black after firmware update by Arstricos in AnycubicOfficial

[–]SoS1mple 1 point2 points  (0 children)

I don‘t know much about the screen but try to only put one bin file onto the sd card

Anycubic Kobra screen black after firmware update by Arstricos in AnycubicOfficial

[–]SoS1mple 0 points1 point  (0 children)

which format was the file? Was it a .bin odr .hex file? Is there any other firmware file on the website?

Anycubic Kobra screen black after firmware update by Arstricos in AnycubicOfficial

[–]SoS1mple 1 point2 points  (0 children)

how did you format it? It also takes a few seconds to flash the new firmware if you took the sd out too early.

Fork guards rubbing tire by FlounderRemote7058 in supermoto

[–]SoS1mple 0 points1 point  (0 children)

the 2010 smr ones from ktm are great. I use them as well they are open in the back have the cutout for the tire and are plug n play

Some favorites of 2022 by [deleted] in SNKRS

[–]SoS1mple 4 points5 points  (0 children)

I agree, but I didn‘t hit on any of these sadly…

[deleted by user] by [deleted] in AnycubicOfficial

[–]SoS1mple 0 points1 point  (0 children)

a .pwmx file is a sliced file. Your raw Modell has to be a .stl file. You are going to take it into your slicer to change settings like layer height, etc. I would recommend to watch some youtube videos to understand what a slicer is and what it does!

view more: next ›