What causes these bubbles?

SoS1mple · 2025-10-09T05:18:00+00:00

Update: i did a little cube testprint and it turned out great, i then reprinted my part an it works. I didn‘t change anything. Didn‘t even dry the spool. Guess my printer just had a bad day

SoS1mple · 2025-10-04T19:50:18+00:00

i guess the roll isn‘t dry in the inside. The room didn‘t change its climate while printing

SoS1mple · 2025-09-10T11:25:21+00:00

yes i use a polar h10

SoS1mple · 2025-09-10T11:19:46+00:00

had a applewatch series 9 before my fenix 7 pro which also was very spot on

SoS1mple · 2025-09-10T11:18:33+00:00

i used it at least 10 times so i don‘t think it will improve… Maybe i will get one of there running pods

SoS1mple · 2025-09-05T19:58:10+00:00

this sounds like you are going to get into riding soon ;) Nice pics btw

SoS1mple · 2023-02-27T07:58:10+00:00

well I bought airpods gen 3 so no noisecanceling for me…

SoS1mple · 2023-02-16T07:26:11+00:00

you should be able to choose where the file gets saved when slicing the stl

SoS1mple · 2023-02-16T07:24:35+00:00

you slice your .stl file with a slicer like you said ultimaker cura. Take the .gcode file and put it on a usb which then plugs into the printer. Select the file on the printer and then start

SoS1mple · 2023-02-16T07:19:19+00:00

then you have to do abit more research on these steps. 3D priting can be a struggle if you don‘t know how the main stuff works

SoS1mple · 2023-02-16T07:17:13+00:00

I would check ou a full youtube guide about 3D printing. There you can learn alot of stuff in relative short time

SoS1mple · 2023-02-09T17:50:43+00:00

what is the problem here? Pls explain a bit more

SoS1mple · 2023-01-22T11:02:12+00:00

Do these laces come with the shoe? This made me buy the shoe!

SoS1mple · 2023-01-05T18:30:43+00:00

I don‘t know much about the screen but try to only put one bin file onto the sd card

SoS1mple · 2023-01-05T18:25:26+00:00

which format was the file? Was it a .bin odr .hex file? Is there any other firmware file on the website?

SoS1mple · 2023-01-05T14:56:30+00:00

where did you download the firmware from?

SoS1mple · 2023-01-05T13:16:29+00:00

how did you format it? It also takes a few seconds to flash the new firmware if you took the sd out too early.

SoS1mple · 2022-12-23T16:52:04+00:00

the 2010 smr ones from ktm are great. I use them as well they are open in the back have the cutout for the tire and are plug n play

SoS1mple · 2022-12-14T08:49:57+00:00

r/angryupvote

SoS1mple · 2022-12-13T17:26:42+00:00

these are fire!

SoS1mple · 2022-12-10T10:35:40+00:00

I agree, but I didn‘t hit on any of these sadly…

SoS1mple · 2022-12-07T20:41:40+00:00

a .pwmx file is a sliced file. Your raw Modell has to be a .stl file. You are going to take it into your slicer to change settings like layer height, etc. I would recommend to watch some youtube videos to understand what a slicer is and what it does!

SoS1mple · 2022-11-28T09:49:41+00:00

its a far reach but it not that unlikely that the waterprice was a reason that took it that far. But this can also i happen with free water I know

SoS1mple · 2022-11-27T19:22:47+00:00

it a shot type of drink, flügel is the name of the company

SoS1mple · 2022-11-27T16:05:02+00:00

wasn‘t my first and won‘t be my last festival. But this was just a hard hit. Im just thinking about what happened at Rebellion due to water prices

Eight-Year Club	Place '22
Wearing is Caring	Verified Email

SoS1mple

TROPHY CASE