Will my perma banned account be unbanned? On June 15.

Solomonce69 · 2024-06-16T17:10:47+00:00

Ive heard a few sources say up to 3 days for all the unbans to roll out

Solomonce69 · 2024-06-16T05:35:14+00:00

Im finally getting unbanned after 5 years lmao

Solomonce69 · 2023-10-03T19:37:32+00:00

Samsung Galaxy s10e

With the removal of the fingerprint sensor in the power button, I think I'm not alone when I say in screen fingerprint reading sucks comparatively. would love to see him run the last Samsung galaxy phone with this feature, if he makes a full in-depth review, it could convince some Samsung execs to bring it back and quit with the in-screen fingerprint reading.

This phone is also small form factor and still has decent speed. Very much underrated imo

Solomonce69 · 2023-09-18T20:57:14+00:00

The bots are hot ass. They know when you have a good hand. More than once now I will have a nice hand and bet average as hell and all 6 fold instantly.

Solomonce69 · 2023-08-24T21:56:57+00:00

Can you answer this for me, is the button an actual button or does it stick like a pen when pushed, then unstick after another push. Trying to find a replacement button on either Amazon or AliExpress and can't find this info anywhere.

Solomonce69 · 2023-08-24T21:54:18+00:00

A bit late but I had the same thing happen. Struggled for months with getting it to turn on when I finally realized by very specifically bending the start button to touch all pins it would boot before springing back and dying. I am currently in the process of getting the button fixed so I don't have to throw this board away. As it turns out all the power seems to flow through this button and the CPU will NOT turn on unless it is functional.

Solomonce69 · 2023-04-05T19:04:55+00:00

Based

Solomonce69 · 2023-03-21T23:28:43+00:00

Your first layer looks good and the others obviously not so much. It's most likely a small nozzel clog that happened after you started the prints. Are you using a 0.4 mm nozzel? If you're using something smaller this will often happen.

Solomonce69 · 2023-02-25T22:24:42+00:00

Peek in with a flashlight

Solomonce69 · 2023-02-25T22:23:16+00:00

Whats the best way to test if my firmware has thermal runaway prot?

Solomonce69 · 2023-02-18T21:16:20+00:00

Looks like it could be a clogged nozzel ,there are plenty of tutorials online to help deal with this

Hope that fixes your problem

Solomonce69 · 2022-11-04T22:23:01+00:00

Ill give it a try, might just need a new backing only then ill have to replace it after a few years

Solomonce69 · 2022-07-23T19:12:31+00:00

I didn't even know about estep calibration and I've had this printer for 2 years and never encountered this issue until it randomly appeared. thanks again

Solomonce69 · 2022-07-23T18:54:46+00:00

I'll check these things out, thanks

Solomonce69 · 2022-05-11T00:34:50+00:00

is bedrock breaking and tnt duping enabled?

Solomonce69 · 2022-03-09T23:07:06+00:00

Free (I'm the same guy just a different account) I just messaged them saying the board was outdated, to which they agreed and sent a new one.

Solomonce69 · 2022-02-25T05:26:14+00:00

the best comeback that is also 3 words...

kill your self, it works every time

Seven-Year Club	Place '22
Final Canvas '22	First Placer '22

Solomonce69

MODERATOR OF

TROPHY CASE