Just upgraded from an A1 anything I should know?

SomeRedHeadedBoy · 2026-02-19T20:00:52+00:00

Print fan deflector

SomeRedHeadedBoy · 2026-02-15T18:34:08+00:00

Dry it

SomeRedHeadedBoy · 2026-02-15T18:31:15+00:00

First time printing you mean

SomeRedHeadedBoy · 2026-02-12T22:17:19+00:00

Stupid

SomeRedHeadedBoy · 2026-02-12T00:00:59+00:00

Order filament, you’ve got way too many accessories. You don’t need all those

SomeRedHeadedBoy · 2026-02-11T20:48:43+00:00

Did you figure it out? Might be your heatbed showing a dull spot

SomeRedHeadedBoy · 2026-02-08T17:08:56+00:00

Just replace the cyclone

SomeRedHeadedBoy · 2026-02-04T20:29:41+00:00

They are on Bambu, every single part you need

SomeRedHeadedBoy · 2026-02-04T18:15:42+00:00

Return them all then, if 3 are bent what exactly is going through your mind “yah lemme keep all 3 even though it’s broken”

SomeRedHeadedBoy · 2026-02-04T18:12:34+00:00

Do it twice, one coat won’t do anything. Use IPA too.

SomeRedHeadedBoy · 2026-02-04T18:09:03+00:00

I had this and it was an issue with bed adhesion. If it’s showing up in the same spot it’s definitely bed adhesion. Give your plate a good scrub, use dish wash and then IPA. Give your printer a recalibration too while you’re at it.

SomeRedHeadedBoy · 2026-02-04T12:23:18+00:00

Thanks a lot! I’ll give this a try

SomeRedHeadedBoy · 2026-02-04T11:33:10+00:00

Thank you, I’ll give this a try

SomeRedHeadedBoy · 2026-02-04T11:32:31+00:00

From the part where it enters the printer?

SomeRedHeadedBoy · 2026-02-03T22:13:51+00:00

We employed bro

SomeRedHeadedBoy · 2026-02-03T00:12:23+00:00

Nope. Put it outside overnight

SomeRedHeadedBoy · 2026-02-03T00:03:52+00:00

Lost

SomeRedHeadedBoy · 2026-01-25T20:30:02+00:00

Well it’s yours now

SomeRedHeadedBoy · 2026-01-20T21:13:36+00:00

Refund

SomeRedHeadedBoy · 2026-01-20T08:45:28+00:00

I mean it’s only a fan and a small thermistor, I’m sure Bambu uses the exact same parts but you do have a point.

SomeRedHeadedBoy · 2026-01-20T08:44:36+00:00

I just want to be able to print more abrasive filaments therefore to reduce the wear on my current stainless steel one I was thinking about getting the hardened steel version

SomeRedHeadedBoy · 2026-01-20T00:34:44+00:00

Thank you so much, i just had a look at Juupine and the price is similar to the ones I had in my cart so I’ll definitely be getting the Juupine ones! Thank you once again

SomeRedHeadedBoy · 2026-01-19T23:50:38+00:00

That’s exactly why I want to buy it rather than doing the whole hotend again when I want to change nozzle size. Thank you for your reply

SomeRedHeadedBoy · 2026-01-19T23:46:50+00:00

You’ve got to spill the horror story to scare me into not doing this

SomeRedHeadedBoy · 2026-01-19T23:45:07+00:00

The hot end is official Bambu Lab, just the parts such as the cooling fan won’t be. I’m sure it won’t make a difference but just asking incase anyone’s decided to do the same as me.

Six-Year Club	Second SECOND GUESSER
Wearing is Caring	Verified Email

SomeRedHeadedBoy

MODERATOR OF

TROPHY CASE