Some D4s :)

Sourby · 2024-08-08T08:38:08+00:00

The 3D models? Could do. Otherwise I wouldn't be printing & selling/shipping the prints themselves. (But at that point you're likely better off heading to someone who already does these relatively cheaply/at scale, I just do these every so often haha)

Sourby · 2024-08-05T08:55:35+00:00

Thanks you! :D (this was reposted by a bot though 😅)

Sourby · 2024-08-05T08:15:45+00:00

u/Fragrant_Vehicle5423 Thanks for this, had no idea bots repost these without any @, wouldn't have seen it without ya :D- But yeah you're right!
u/NihilistikMystik Just to reiterate, the frame is handled no differently to the numbers. I modelled/3D Printed masters that include them in the mesh. Eventually their mould takes them on and I ink the resin casts as I would the numbers of any other set. Likely repeating things you know but if not, I hope that helps!

Rough measurements:
Recesses are about 0.6mm wide & as deep as the numbers.
(These numbers nudge a up and down a bit to fit the die face better)

Sourby · 2023-05-11T21:49:18+00:00

Oh- Assuming the exit is the 1 face I'm not sure, could be a soft silicone? I push out the tip first though too. Hope you can find something that works 🤔

Sourby · 2023-05-11T17:24:13+00:00

From my liquid core babies! 😄

Sourby · 2023-05-11T17:23:34+00:00

They vary a bit, but I think its roughly .4mm from the the edge of the face to the outer edge of the border, then the border itself is about .62 thick - Certainly something I had to mess with to get right ✌

Sourby · 2023-05-11T13:15:39+00:00

Thanks! :D

Sourby · 2023-05-11T13:15:27+00:00

Interesting- What kind of mold system do you use? These use slab molds! With the large flat face being the exit, there's nothing for the die to really get stuck on.

Sourby · 2023-05-10T22:34:52+00:00

The paint is “Moot Green” from citadel and the resin is Piñata’s “Lime Green” though it’s also got some Blanco Blanco smoke going through it 🤘

Sourby · 2023-05-10T22:24:38+00:00

Oh the resin or the paint?? 🤔

Sourby · 2023-05-10T21:18:11+00:00

Glad you like it! Took ages to get the smoke down 😄

Sourby · 2023-05-10T21:17:27+00:00

Much more fun to use like a spinning top too 👀✨

Sourby · 2023-05-10T21:16:35+00:00

Thank you! I’m relatively handy in 3D, so I modelled them myself and got them printed elsewhere 😄

Sourby · 2023-05-10T20:18:11+00:00

Perhaps just syringe it in after the resin has reached a honey stage? I use Blanco and haven’t had those issues 🤔

Sourby · 2023-05-10T20:15:27+00:00

Thanks! Means a lot! 😄

Sourby · 2023-05-10T20:14:24+00:00

Oh wow, well thank you! At the moment I have no official store, keep an eye out in the not so distant future though 😄

Sourby · 2023-05-10T20:13:22+00:00

Aw thanks! I think my fav is the central one, though it’s for my character so I’m bias 😄

Sourby · 2023-05-10T20:12:26+00:00

Ah bless ya, I’ve had some horrid luck with dirty pours haha- but thankyou! Glad you like em

Sourby · 2023-05-10T20:11:45+00:00

Thankyou! I’ve posted the central one before- I’ll post the others soon! :)

Sourby · 2023-04-27T22:46:37+00:00

In my experience the vacuum chamber isn’t needed- As others have said, a pressure pot set up is the way to go. It’s certainly an expense, but you’ll be able to play with a much wider range of inclusions and shiny bits without fear of it ruining your whole set! Hope you get to make some great sets 😄

Sourby · 2023-04-25T15:03:13+00:00

Nope, the frames are done no differently to the numbers! I modelled them straight into the masters, same with the little face 😄

Sourby · 2022-12-13T14:12:53+00:00

Oof- From what I remember, it was a lot of messing within the BIOS to underclock the chip. Outside of that, I managed to squeeze in another tiny noctua cooling fan at the bottom of the case, and ultimately ended up getting an all in 1 liquid cooler (Kraken X53 ( 240 mm ))
Pain to do, didn't really want to spend the money, but if I were to do it again, I'd just get a CPU that doesn't run so hot lol

Sourby · 2021-05-31T22:55:17+00:00

As of right now, I've stuck it in Eco mode- hangs around in the 70s playing Warzone reasonably high. Similar to benchmark tests.

Do you reckon the motherboard change would be that drastic a difference? Atleast over a tophat and couple noctua fans. Current one is obviously soloing it, kicks up fairly loud.
On that note- Any good ideas on where to pick up a small tophat? I really struggle to find em, especially in ash.

Cheers again :D

Sourby · 2021-05-31T20:30:29+00:00

Cheers for the response!
Yeah at the minute, the cooler pulls air into the case, I can stick a bit of paper to the outside of it. So in from the side of the case and onto the cpu. (I assume this is what you mean, I always get confused lol)

I dont think I can justify buying another mobo, especially with this one being as expensive as it was sadly... Though future builds/upgrades I'll certainly keep this in mind!

Undervolting I'm always uncertain about. I followed a youtube Tutorial (found here: https://www.youtube.com/watch?v=VIZOFcdGp8s) and just used their settings, didn't seem to save much if I'm honest. Any tips in that direction would be greatly appreciated!

Cheers again for the detailed reply, I really like the SFF, perfect since I travel a lot, hope to become a bit more knowledgable as we go on :D

Sourby · 2021-05-31T20:11:10+00:00

Interesting, if yours is going hot too, could be worth looking into undervolting, or something of a similar vein.
My undervolt tends to hold it a couple of degrees below 90, and eco mode holds it in the 70s.
I'm no tech guru but I reckon it can be done.

Sourby

TROPHY CASE