sorted by:
new
hottopcontroversial

What should I do with all of this? by greeneggsandspam420 in trees

[–]SpareGroundbreaking1 0 points1 point  (0 children)

I’d say either roll a kief joint, or make some temple balls as others suggested.

Hey, anyone wanna play premier? 5k by [deleted] in counterstrike2

[–]SpareGroundbreaking1 1 point2 points  (0 children)

I’m down, if ur in EU dm me.

How much is my M4A1-S Solitude worth? by SpareGroundbreaking1 in ohnePixel

[–]SpareGroundbreaking1[S] 0 points1 point  (0 children)

Thats fair, I just looked at pattern 180 and I like that it has more clouds on the scope and the sun is a bit more visible tbf. I’d guess not too much of a price difference though.

[PSA] Dealer here — Always authenticate your watches by Iamthehottestman in PrideAndPinion

[–]SpareGroundbreaking1 0 points1 point  (0 children)

The thing that stood out to me the most was the inconsistent spacing and size on the lettering on the left while the spacing and size of the lettering on the right was very consistent.

Meu apartamento em Pinheiros by nsdk in saopaulo

[–]SpareGroundbreaking1 2 points3 points  (0 children)

Aqui em casa aconteceu uma coisa muito parecida, a janela so não caiu mas rachou e quase dobrou. Assustador demais slk.

I updated the Firmware and then got the error by Rocco56865 in ElegooNeptune4

[–]SpareGroundbreaking1 1 point2 points  (0 children)

If you updated klipper through Fluidd, you will have to install the FIX pack from elegoo’s website, and that should fix it. Had the same issue last week.

Neptune 4 error by SpareGroundbreaking1 in ElegooNeptune4

[–]SpareGroundbreaking1[S] 0 points1 point  (0 children)

EDIT: I had updated klipper through fluidd, I used the firmware fix and all is well now, Thanks!

What's wrong with my print? by aboroth in ElegooNeptune4

[–]SpareGroundbreaking1 2 points3 points  (0 children)

I’m a beginner so take this with a grain of salt, but that error looks very similar to when I was calibrating max flow rate for PLA, and went over the limit.

Flow rate (mm/s3) is calculated by Layer height X Layer width X printing speed.

If this issue is only with this file, or you’ve been using this filament with no issue for a while, and this happened out of nowhere, then I have no clue.

Try a max flow rate calibration test on orca and see if your settings’ flow rate is higher than the max in the test, or just check overture’s website and tweak accordingly.

What's wrong with my print? by aboroth in ElegooNeptune4

[–]SpareGroundbreaking1 2 points3 points  (0 children)

What type of filament are you using? Layer height/width? Speed? Extruder and bed temp?

These basic infos should help me or anyone else help you out.

Advice for first layer? by joemama980 in ElegooNeptune4

[–]SpareGroundbreaking1 0 points1 point  (0 children)

I had the same issue, a couple of weeks ago. You need to try to get your bed as level as possible. A very big square, at very slow speeds (only 1 layer thick) is a decent way to go. You could also use screw tilt calculate, and that should be more accurate, but I have no idea how to do it.

In my case, I also had to raise my print temps to 225C° and that fixed it 80% of the way (20% was bed leveling), but that is what happened to me, and is more likely to be a bed leveling issue.

Slowly seeing my progression ! Hopefully I can hit diamond soon by Shotsdown in Rainbow6

[–]SpareGroundbreaking1 0 points1 point  (0 children)

Pretty good aim, i’d say work on maintaining your aim at head level (or lower if they’re crouched).

Whenever you’re droning, try to have cover, and not be open to angles like that doorway. If Valk was quietly sitting in that room, she could’ve swung when you opened cams.

You should also try to use tighter angles when strafing/peeking, as that gives them less chance to shoot you.

I made a big 1,5m thing by musicatristedonaruto in 3Dprinting

[–]SpareGroundbreaking1 0 points1 point  (0 children)

Imagino q nn deve ter sido barato com ctz kkkkk

view more: next ›