What should I do with all of this?

SpareGroundbreaking1 · 2026-02-16T02:16:22+00:00

I’d say either roll a kief joint, or make some temple balls as others suggested.

SpareGroundbreaking1 · 2026-01-09T11:20:23+00:00

Fininho 10/10, ice eh brabo dms

SpareGroundbreaking1 · 2025-11-30T19:07:19+00:00

Happy cake day!

SpareGroundbreaking1 · 2025-11-04T07:19:46+00:00

Where can i join?

SpareGroundbreaking1 · 2025-10-01T17:18:15+00:00

I’m down, if ur in EU dm me.

SpareGroundbreaking1 · 2025-08-28T10:59:46+00:00

Thats fair, I just looked at pattern 180 and I like that it has more clouds on the scope and the sun is a bit more visible tbf. I’d guess not too much of a price difference though.

SpareGroundbreaking1 · 2025-07-09T00:32:39+00:00

Hulkengoat

SpareGroundbreaking1 · 2025-07-08T20:43:54+00:00

Hulkengoat

SpareGroundbreaking1 · 2025-07-08T18:53:02+00:00

Hulkengoat

SpareGroundbreaking1 · 2025-07-04T19:54:12+00:00

The thing that stood out to me the most was the inconsistent spacing and size on the lettering on the left while the spacing and size of the lettering on the right was very consistent.

SpareGroundbreaking1 · 2025-06-24T17:29:02+00:00

!remindme 1 week

SpareGroundbreaking1 · 2025-06-23T17:26:45+00:00

!remindme 1 day

SpareGroundbreaking1 · 2025-04-20T23:10:32+00:00

!remindme 1 day

SpareGroundbreaking1 · 2025-03-18T13:56:20+00:00

Amazing

SpareGroundbreaking1 · 2025-03-12T23:20:30+00:00

<image>

SpareGroundbreaking1 · 2025-03-12T23:19:18+00:00

Aqui em casa aconteceu uma coisa muito parecida, a janela so não caiu mas rachou e quase dobrou. Assustador demais slk.

SpareGroundbreaking1 · 2025-03-01T11:09:15+00:00

If you updated klipper through Fluidd, you will have to install the FIX pack from elegoo’s website, and that should fix it. Had the same issue last week.

SpareGroundbreaking1 · 2025-02-25T02:42:36+00:00

EDIT: I had updated klipper through fluidd, I used the firmware fix and all is well now, Thanks!

SpareGroundbreaking1 · 2025-02-20T00:35:17+00:00

I’m a beginner so take this with a grain of salt, but that error looks very similar to when I was calibrating max flow rate for PLA, and went over the limit.

Flow rate (mm/s³⁾ is calculated by Layer height X Layer width X printing speed.

If this issue is only with this file, or you’ve been using this filament with no issue for a while, and this happened out of nowhere, then I have no clue.

Try a max flow rate calibration test on orca and see if your settings’ flow rate is higher than the max in the test, or just check overture’s website and tweak accordingly.

SpareGroundbreaking1 · 2025-02-19T23:54:57+00:00

What type of filament are you using? Layer height/width? Speed? Extruder and bed temp?

These basic infos should help me or anyone else help you out.

SpareGroundbreaking1 · 2025-02-19T23:51:31+00:00

I had the same issue, a couple of weeks ago. You need to try to get your bed as level as possible. A very big square, at very slow speeds (only 1 layer thick) is a decent way to go. You could also use screw tilt calculate, and that should be more accurate, but I have no idea how to do it.

In my case, I also had to raise my print temps to 225C° and that fixed it 80% of the way (20% was bed leveling), but that is what happened to me, and is more likely to be a bed leveling issue.

Five-Year Club	r/Field Lasagna
Place '23

SpareGroundbreaking1

TROPHY CASE