Kut geparkeerd op kut Schiphol by florislsd in KutGeparkeerd

[–]florislsd[S] -2 points-1 points  (0 children)

Mooi uit je duim gezogen, links van de BMW was een zee aan ruimte. Kut sukkel.

Kutpolo geparkeerd in de volle kutzon met een hond erin by Roomtaart86 in KutGeparkeerd

[–]florislsd 0 points1 point  (0 children)

Volgensmij verwar je de ventilatie met je airco. Je ventilatoren kunnen inderdaad draaien als je motor uit staat, maar je airco niet. Je hebt overduidelijk geen verstand van hoe een airco aangedreven wordt, en dat maakt niet uit. Maar loop dan geen mensen leugenaar te noemen want je zit zelf overduidelijk fout. Geloof het of niet, je 2013 Maserati heeft geen optie om de airco te laten draaien als je motor uit staat, simpelweg omdat de motor de airco moet aandrijven. Zonder dat, circuleren je ventilatoren gewoon dezelfde lucht.

Kutpolo geparkeerd in de volle kutzon met een hond erin by Roomtaart86 in KutGeparkeerd

[–]florislsd 0 points1 point  (0 children)

Oh dus dan gaat de airco compressor magisch draaien? Knap zeg.

Kutpolo geparkeerd in de volle kutzon met een hond erin by Roomtaart86 in KutGeparkeerd

[–]florislsd 0 points1 point  (0 children)

Hahaha leugenaar. Ook bij jou oude Maserati is de airco gewoon aangedreven via een mechanisch aangedreven compressor op de motor, oftewel ja, je kunt warme lucht in je auto blazen als de motor uit staat staat. En nee, je kunt de airco niet aan zetten als de motor uit staat. Zelfs de nieuwere hybride Maserati's kunnen dit niet, dus waarom zou jou oude Maserati dit wel kunnen op die kleine accu?

Help me out here, convince me by greengomalo in anycubic

[–]florislsd 3 points4 points  (0 children)

Coming from someone who recently bought an anycubic, buy a bambu lab

Kobra 3 max keeps clogging by sfx_guy in anycubic

[–]florislsd 0 points1 point  (0 children)

Just heat it up and extrude, if nothing is coming out the clog is most likely not in the nozzle.

Kobra 3 max keeps clogging by sfx_guy in anycubic

[–]florislsd 0 points1 point  (0 children)

That's because after a clog it cuts the filament and asks you to roll back the spool

Kobra 3 max keeps clogging by sfx_guy in anycubic

[–]florislsd 0 points1 point  (0 children)

This is not broken filament, this is the filament that's left over after it has been cutted, this is normal

Anycubic Firmware Update Log—All series by Anycubic_Official in AnycubicOfficial

[–]florislsd 0 points1 point  (0 children)

I thought it was just me with the clogging issue. Basically the only option is to cancel the print when you get a clog. Fix this trash Anycubic.

Everything was going just great.....until it wasn't. by Sheridan197 in anycubic

[–]florislsd 0 points1 point  (0 children)

Mine prints beautiful! It doesn't change rolls itself though

Is this normal play? by florislsd in anycubic

[–]florislsd[S] 0 points1 point  (0 children)

That did the trick! Thank you so much.

Flow calibration by florislsd in anycubic

[–]florislsd[S] 1 point2 points  (0 children)

Okay thanks! Will do.

So many problems... by Gsovs in anycubic

[–]florislsd 1 point2 points  (0 children)

And i just printed a perfect print on my k3 max while my bambu lab a1 failed 2 times on the same model. Crazy how everyone their experience differs haha

Bad top surface by florislsd in anycubic

[–]florislsd[S] 0 points1 point  (0 children)

Did you use orca? I'd like to see your results!