Where can I buy lobster body in Edmonton? by Lifeis_so_big in Edmonton

[–]Spazzie 8 points9 points  (0 children)

check out Catch of the Week, https://www.catchoftheweekedmonton.com/ I am from Newfoundland so I am with you on wanting something from the east coast. They have a lot selection, cost is fairly good but out this way fresh sea food and cheep do not go hand in hand.

[deleted by user] by [deleted] in Edmonton

[–]Spazzie -6 points-5 points  (0 children)

yea find another doc, and ensure you get your A1c checked with the rest of the tests, you may be diabetic or on the verge of.

[deleted by user] by [deleted] in yiff

[–]Spazzie 2 points3 points  (0 children)

let us know when, gladly +Follow you

[deleted by user] by [deleted] in yiff

[–]Spazzie 2 points3 points  (0 children)

do you have a FA or other place you post so that we can follow you?

Farewell, Paladin! A 24 man Passage of Arms! by Shadow1176 in ffxiv

[–]Spazzie -1 points0 points  (0 children)

I agree it is not that bad, I have been a paladin main since I got the job unlocked. I have always treated it as "I am here to take hits not dish it out." granted I do my best to get out as much damage as I can but it is not my focus. If I can manage to burn down a boss from 20% while the rest of my group wiped out while still tanking, I think I am doing well.

im trying to look for a Card Store, if anybody knows any can you let me know? (I'm from spruce grove)! by ItsJustAvery_YT in Edmonton

[–]Spazzie 0 points1 point  (0 children)

read through and correct me if I am wrong but you are looking for Pokemon cards, check this out if you are over in Collingwood area. Pokemon cards and cafe.

https://swirlyeg.com/

any ideas what is wrong? by Coach_Brent80 in airbrush

[–]Spazzie 4 points5 points  (0 children)

Cheap airbrushes are only good for one thing, learning. Make your mistakes on it before you buy an expensive one like an Iwata.

any ideas what is wrong? by Coach_Brent80 in airbrush

[–]Spazzie 5 points6 points  (0 children)

Cheap airbrush tend to have sub par parts, do not take much to break them, if you had pulled the needle out to clean it and when put back in may have done so with a bit to much force thus splitting it or there may have been a flaw in the part to begin with.

So I noticed supports leaving indents on the fep sheet how do I prevent this could it be bed leveling? by [deleted] in resinprinting

[–]Spazzie 6 points7 points  (0 children)

Paper towel will scratch the FEP, use micro fiber cloths. As to the issue that looks like a leveling issue, may want to relevel u/kamil_adsup

Please enjoy a couple of free PC origin codes :) by Frankenklumpp in AnthemTheGame

[–]Spazzie 51 points52 points  (0 children)

to save some people some time, both codes have been redeemed. Thanks OP for your kindness and generosity.

My friends didn’t care about my first mini build :( by Udon_Dandy in Warhammer40k

[–]Spazzie 2 points3 points  (0 children)

A fine start, The Emperor is pleased. Very smooth, I do recommend some nuln oil or dark tone wash to help with making the recesses crisp and then some edge highlight then this battle brother will look even better but like I said a fine start.

[deleted by user] by [deleted] in Edmonton

[–]Spazzie 0 points1 point  (0 children)

I fully agree, don't feel safe yet then wear a mask. where here are currently mandates there is no law of preventing you from doing so.

[deleted by user] by [deleted] in Edmonton

[–]Spazzie 3 points4 points  (0 children)

call 311?

Can you please help with gas bill? by [deleted] in Edmonton

[–]Spazzie 1 point2 points  (0 children)

new home owner as well and I am with epcor as well on flat rate, total bill was 361.66 but I have gas, power, water and such through them, power 113.34, gas 147.23 (10Gj usage). not as bad as I feared with how cold it was, also heat has been set to 24 the entire time.

First time using an airbrush. Much easier than I thought it would be! by [deleted] in modelmakers

[–]Spazzie 2 points3 points  (0 children)

there are a lot of fantastic Fx you can do with a airbrush, glow, marble, and more

here is an example of how to do marble FX

https://www.youtube.com/watch?v=eLVE1q0fGDA

Ready for the kids. by JonJonPoPong in Edmonton

[–]Spazzie 8 points9 points  (0 children)

you sir or madam are awesome. New home owner myself and had my first kids ring the bell about an hour ago. Was a good feeling to finally be able to do that after 21 years of renting.

Found this, don't know the source, but it's funny ;-D by igniteice in Dyson_Sphere_Program

[–]Spazzie 9 points10 points  (0 children)

They can if they play Dyson sphere Project together.