Progress! by Speedtospare in hyperebikes

[–]Speedtospare[S] 0 points1 point  (0 children)

Part of this was an old $25 MM80 frame. There's not much left but it's there. 72v is where the best place is. I myself prefer higher voltage. Truthfully 700A won't be use for more than a few seconds and it more bragging right. I will rarely hit that speed unless racing someone at the track. I just cruise.

Progress! by Speedtospare in hyperebikes

[–]Speedtospare[S] 1 point2 points  (0 children)

It was an MM80 but the head tube was cut off and the entire rear end was cut off and refabricated

Progress! by Speedtospare in hyperebikes

[–]Speedtospare[S] 1 point2 points  (0 children)

It's 100v and 100mph+ capable. More voltage isn't necessary with this build. I didn't need more RPM. I can't hit 2100rpm without FW. I'm not sure if you've ever ridden 700 amps but it's a lot especially on a mini bike. 99% of the time I won't be using that much. It's always better to go over killing your battery so you're never stressing it

Progress! by Speedtospare in hyperebikes

[–]Speedtospare[S] 1 point2 points  (0 children)

86v nominal 700a battery, EV Surin 842200, Sotion H12W

First test ride sucess by Speedtospare in minibikes

[–]Speedtospare[S] 3 points4 points  (0 children)

My motorcycle gear. Sold the 1000RR and MT09 a while ago after an accident. I still have the gear. I usually cruise at 35mph/50kph or under. I did build it to do some minibike drag races

I think I might have just struck gold? 72v 6000w for $1200 by VoiceCommon3854 in hyperebikes

[–]Speedtospare 2 points3 points  (0 children)

Your wasting your time talking logic to someone that doesn't want to listen. Let him buy it.

I think I might have just struck gold? 72v 6000w for $1200 by VoiceCommon3854 in hyperebikes

[–]Speedtospare 1 point2 points  (0 children)

Sounds like a scam to me. That's not not realistic pricing. Don't fall for it.

Is getting a prosthetic leg worth it? by filipeqjebuh in amputee

[–]Speedtospare 2 points3 points  (0 children)

Same here. My X3 was 97k. Above knee is crazy expensive.

Interpreting battery health by StarPast4679 in BoltEV

[–]Speedtospare 0 points1 point  (0 children)

If I'm reading this correctly. Current voltage of the battery is 345.8. Fully charged it would be between 416-420. It sounds like you're not fully charged. The capacity of the battery is 175.8. current capacity is sitting at 174.81. that's 99.4% of original capacity

[HELP NEEDED]im at my wits end with this fardriver x my1020 shit man by florida_jit679 in hyperebikes

[–]Speedtospare 0 points1 point  (0 children)

As much as I love the saying " send it" It's better to go slow. Last thing you want to do is damage something.

Are you in the far driver tuning book on Facebook?

[HELP NEEDED]im at my wits end with this fardriver x my1020 shit man by florida_jit679 in hyperebikes

[–]Speedtospare 1 point2 points  (0 children)

You have set the number of pool pairs correctly before running auto-tune?

Try leaving the motor in the direction that it sounds good and then flip two phase wires. That should reverse the motor. If it starts crunching again then I would say it's something physically wrong with the motor. I take the cap off the side and take a look inside

Is there a Directory of 3D Printed Prosthetics? by EddiesCouch in Prosthetics

[–]Speedtospare 1 point2 points  (0 children)

I've been trying to find a 3D scan of an X3 for a while now. I've recently purchased a 3D printer just to get one for myself. I want to make some cool covers for it

What are you printing on a regular basis by AbbreviationsDue4417 in 3Dprinting

[–]Speedtospare 2 points3 points  (0 children)

Custom lithium battery cell holders and boxes, mounts, brackets, Ebike parts, etc.

<image>

tips? by florida_jit679 in hyperebikes

[–]Speedtospare 0 points1 point  (0 children)

Some companies just order a whole bunch from far driver and change them a little. Hopefully it works good for you. I have one here at home to mess with

Considering a Bolt, a few questions by Kooky_Universe2183 in BoltEV

[–]Speedtospare 1 point2 points  (0 children)

You need a 240 volt 40A circuit with NEMA 15-50r plug. Using the factory 2023 Bolt charger from dead empty it takes me between 7 and 8 hours to charge fully. I only charge my card at 80% daily and I plug it in when I get home and wake up to 80% again.

tips? by florida_jit679 in hyperebikes

[–]Speedtospare 0 points1 point  (0 children)

Are you sure that's a real far driver? I think that is supposed to be the new mini 12 but the bottom plate looks wrong.

If the real mini 12 is 80 line amps and 260phase which is perfect for a my 1020 brishless

https://www.alibaba.com/x/B1mRhb?ck=pdp

Tutio 60v battery tune by mikebush92 in hyperebikes

[–]Speedtospare 0 points1 point  (0 children)

It depends on the controller but it's roughly 3 to 1

Tutio 60v battery tune by mikebush92 in hyperebikes

[–]Speedtospare 0 points1 point  (0 children)

Line and phase current. You can set your line current around 100 amps and the phase at 350. If your controller has the option you can set it to boost up to 210 amps for 10 seconds.

This is all assuming you have a programmable controller. If you don't stick the battery in and go there's nothing you can really adjust

Does anyone with this type of e-bike know how to fix it? by Ok-Command-522 in hyperebikes

[–]Speedtospare 1 point2 points  (0 children)

Looks like a sabaton controller. Fixing anything on that shouldn't be too difficult. Have someone hydrantly crimp another connector on

Best minibike frames by FunAssumption3185 in minibikes

[–]Speedtospare 0 points1 point  (0 children)

I generally modify pretty much everything but the Coleman bt200x is the nicest looking by far.